Results 1 to 10 of about 1,188 (162)
Squeeze Casting of Semiolid A356 Alloy [PDF]
Advances in Mechanical Engineering, 2014 The rheo-squeeze casting (rheo-SQC) combining the rheocasting and the SQC was developed, in which semisolid slurry was produced by the low superheat pouring with a shearing field (LSPSF) process. The three-dimensional morphology of the primary α-Al phase
Xiang-Jie Yang +4 more
doaj +2 more sources
Research progress on squeeze casting in China [PDF]
China Foundry, 2014 Squeeze casting is a technology with short route, high efficiency and precise forming, possessing features of casting and plastic processing. It is widely used to produce high performance metallic structural parts.
Li Yuanyuan, Zhang Weiwen, Zhao Haidong
doaj +1 more source
Optimization of Squeeze Casting Parameters for 2017 A Wrought Al Alloy Using Taguchi Method
Metals, 2014 This study applies the Taguchi method to investigate the relationship between the ultimate tensile strength, hardness and process variables in a squeeze casting 2017 A wrought aluminium alloy.
Slim Souissi +2 more
exaly +3 more sources
Microstructure evolution and mechanical properties of Mg-12Zn-2Y alloy containing quasicrystal phase fabricated by different casting processes [PDF]
China Foundry, 2021 Although icosahedral quasicrystal phase (denoted as I-phase) has been verified as an outstanding reinforcing phase, the mechanical properties of quasicrystal-reinforced Mg-Zn-Y alloys fabricated by traditional casting processes are still unsatisfactory ...
Ji-guang Liu +2 more
doaj +1 more source
Mechanical and Tribological Behavior of Gravity and Squeeze Cast Novel Al-Si Alloy
Metals, 2022 The automotive industry traditionally reduces weight primarily by value engineering and thickness optimization. However, both of these strategies have reached their limits.
Vadlamudi Srinivasa Chandra +5 more
doaj +1 more source
Crystals, 2022 Al-8Zn-2Mg-1.5Cu-0.15Sc-0.15Zr alloy with high-strength performance as well as good castability has been developed. In this study, effects of electromagnetic stirring melt treatment (ESMT) on microstructure and mechanical properties of the alloy in the ...
Yongtao Xu +5 more
doaj +1 more source
Materials Research Express, 2021 Al–Si–Cu alloy oil pump casings used in heavy automotive were produced through gravity die casting process. The customer requirement of 80–125 BHN with a ductility of 3% was not attainable with gravity die casting process.
C Manikandan +2 more
doaj +1 more source
Effect of pressures on macro-/microstructures and mechanical properties of A380 aluminum alloy
工程科学学报, 2017 This study investigated the microstructures and the mechanical properties of the A380 alloy solidified at different squeeze pressures by polarizing microscopy, scanning electron microscopy, image analysis, and tensile test. The obtained results show that
YU Bai-shui +3 more
doaj +1 more source
Sulaimani Journal for Engineering Sciences, 2015 In this study Al - (0-15 wt %) Y2O3 composites were prepared by both squeeze casting and powder metallurgy routes. It was found throughout this work that Vickers microhardness, compressive yield strength and wear resistance increase continuously with ...
Farouk M. Mahdi, Abd-Ulkader A. Annaz
doaj +1 more source
Effect of heat treatment on microstructure and properties of semi-solid squeeze casting AZ91D
China Foundry, 2020 Semi-solid AZ91D magnesium alloy billets were prepared by near-liquidus heat holding. Semi-solid squeeze casting was conducted at 575, 585 and 595 °C, respectively, with 1 mm·s-1 squeeze speed.
Zhi-yong You +2 more
doaj +1 more source