Results 31 to 40 of about 14,678 (246)
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
工程科学学报Selective laser melting (SLM) is a powder-bed metal additive manufacturing technology that is extensively employed in the fields of marine engineering, biomedicine, and nuclear power due to its high processing precision and wide range of applicable ...
Baoshan WANG, Qiang SHANG, Cheng MAN
doaj +1 more source
Journal of Materials Research and Technology, 2023 In this study, two stainless steel clad plates (STS 316L/A516-70N and STS 304L/A516-70N) were fabricated without Ni interlayers by hot rolling and normalizing under the same conditions, and their microstructures and intergranular corrosion resistances ...
Ju-Chan Jin +5 more
doaj +1 more source
Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading
Advanced Engineering Materials, EarlyView.This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev +2 more
wiley +1 more source
International Journal of Electrochemical Science, 2013 Microbiologically influenced corrosion is a serious problem for stainless steels in marine engineering. In this study, the attachment of a typical biofouling microalgae Chlorella vulgaris on the surface of 316L stainless steel was determined by a light ...
Shuxia Liu, Yi Wang, Dun Zhang, Yi Wan
doaj +1 more source
International Journal of Electrochemical Science, 2020 316L stainless steel has good corrosion resistance and is widely used in oilfield produced water. The environment of oilfield produced water is complicated by corrosion factors such as acetic acid, CO2, high temperature and high pressure, which easily ...
Ping Li +5 more
doaj +1 more source
Metals, 2021 Metallic biomaterials are widely used for implants and dental and orthopedic applications due to their good mechanical properties. Among all these materials, 316L stainless steel has gained special attention, because of its good characteristics as an ...
Bruna Horta Bastos Kuffner +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
دراسة بعض العوامل المؤثرة على لحام المونة لربط الفولاذ مقاوم الصدأ (CK مع الفولاذ منخفض الكاربون ( 15 ( AISI 316L ) [PDF]
Engineering and Technology Journal, 2008 Similar Plates of stainless steel (AISI 316L) and dissimilar plates ofstainless steel (AISI 316L) and low carbon steel (Ck15) are welded by brazingusing copper base non- active filler metal alloys in furnaces with inert gasatmospheres The specimens were ...
doaj +1 more source
Journal of Functional Biomaterials, 2023 In the field of healthcare and dentistry, 316L stainless steel is widely used for its corrosion resistance. However, the presence of lactic acid in salivary solutions can affect its surface reactivity.
Lidia Benea +3 more
doaj +1 more source