Comparison of Stiffness Measurements of Wooden Rods Using Acoustic Guided Wave and Static Bending Test Techniques. [PDF]
Sensors (Basel)Traditionally, mechanical bending tests are used to measure the stiffness of lumber, which is generally represented by the static modulus of elasticity (MoE).
Bakar AHA +4 more
europepmc +4 more sources
Effect of Sample Dimensions on Static Bending Test [PDF]
Floresta e Ambiente, 2020 This study aimed to evaluate the static bending strength (fM) and modulus of elasticity (MOE) to static bending values of Eucalyptus grandis samples produced in different dimensions.
Clarissa Gusmão Figueiró (4660963) +6 more
core +5 more sources
Analytical study of the curve of static bending test for wood specimens [PDF]
Ambiente Construído, 2020 The NBR 7190:1997 "Design of Timber Structures" provides the procedure for several mechanical tests, and among them, the Static bending test for Modulus of Elasticity (Em) and Conventional Value of Strength (fm) determinations.
André Luis Christoforo (4661911) +5 more
core +5 more sources
Static bending test after proximal femoral nail (PFN) removal - in vitro analysis. [PDF]
Rev Bras Ortop, 2017 To evaluate, through biomechanical testing, the resistance to and energy required for the occurrence of proximal femoral fracture in synthetic bone after removal of a proximal femoral nail model (PFN), comparing the results obtained with a reinforcement technique using polymethylmethacrylate (PMMA).Fifteen synthetic bones were used: five units for the ...
Paiva LM +5 more
europepmc +6 more sources
Possible sources of acoustic emission during static bending test of wood specimens [PDF]
Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 2012 The paper is dedicated to identification of sources of acoustic emission generated during static bending test of wood specimen. Information on wood structure, wood failure behavior and computer-generated finite element method (FEM) simulation of static ...
M Fajman +7 more
core +3 more sources
Modelling the Flexural Hysteresis Behaviour of Bretelle Dampers based on A Quasi-static Bending Test
IEEE Transactions on Power Delivery, 2023 International audienceBretelle dampers are made of slack conductor pieces that are used to mitigate aeolian vibration amplitudes. Under cyclic and dynamic excitation, inter-strand friction in slack conductors causes a significant flexural hysteresis ...
Sébastien Langlois +9 more
core +3 more sources
Novel Bending Test Method for Polymer Railway Sleeper Materials [PDF]
, 2021 Alternative sleeper technologies have been developed to address the significant need for the replacement of deteriorating timber railway sleepers. The review of the literature indicates that the railway sleepers might fail while in service, despite ...
Yu, Peng +13 more
core +1 more source
Static Test of a Thermoplastic Composite Wingbox Under Shear and Bending Moment [PDF]
2018 AIAA/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, 2018 The proof of an aircraft’s structural integrity and safety is typically provided by analysis and supported by structural test evidence. The experimental test of a wingbox, which is the main structural component of a wing, can provide useful data on assessment of its structural performance in an actual airplane for the design objectives.
Zucco, Giovanni +9 more
openaire +1 more source
Permanent indentation characterization for low-velocity impact modelling using three-point bending test [PDF]
, 2014 This paper deals with the origin of permanent indentation in composite laminates subjected to low-velocity impact. The three-point bending test is used to exhibit a non-closure of matrix crack which is assumed as a cause of permanent indentation ...
Bouvet, Christophe +3 more
core +1 more source
Structural behaviour of elliptical hollow sections under combined compression and uniaxial bending [PDF]
, 2011 The structural behaviour of elliptical hollow sections (EHS) has been examined in previous studies under the isolated loading conditions of pure compression and pure bending.
Chan, TM +8 more
core +1 more source