Results 61 to 70 of about 24,864 (263)

Effect of Basalt Fiber on Static and Dynamic Mechanical Properties of Metakaolin-Based Cement Clay

Advances in Civil Engineering, 2020
To investigate the effects of basalt fiber content on the mechanical properties and microstructure characteristic of metakaolin-based cement clay, the static and dynamic uniaxial compressive and splitting tensile, nuclear magnetic resonance (NMR), and ...
Kun Huang, Qinyong Ma, Dongdong Ma
doaj   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Simulation‐Based Assessment of Second‐Order Residual Stress Fields on the Fatigue Performance of Silicon‐Strengthened Ferritic Ductile Irons

Advanced Engineering Materials, EarlyView.
This work presents a simulation‐based framework based on representative volume elements (RVEs) that explicitly incorporates process‐induced second‐order residual stresses into the fatigue strength assessment of ductile cast iron (DCI). For the first time, this approach enables a direct evaluation of the influence of second‐order residual stress fields ...
Lutz Horbach, Xuemei Lyu, Jiali Zhang, Felix Weber, Christoph Broeckmann   +4 more
wiley   +1 more source

Laser Metal Powder Deposition of Titanium Microalloyed HSLA Steel FeC0.12Si0.25Mn1.3

Advanced Engineering Materials, EarlyView.
This study investigates the additive manufacturing of titanium‐doped high‐strength low‐alloy (HSLA) steel via laser metal deposition. It reveals distinct process‐structure relationships for elemental powder blends compared to prealloyed feedstocks.
Olaf Stelling, Matthias Steinbacher, Nils Ellendt   +2 more
wiley   +1 more source

EXPERIMENTAL STUDY ON TENSILE PROPERTIES OF HUCK RIVET JOINT

Jixie qiangdu, 2018
Aiming at the phenomenon that the Huck rivet often falls off in the application of rolling stock,the quasi-static tensile test of Huck rivet was carried out by using the universal mechanical testing machine. The tensile performance curve of Huck rivet is
ZHANG XiangFeng, QIN Nan, WANG YongYan
doaj  

Determining the Stages of Deformation and Destruction of Composite Materials in a Static Tensile Test by Acoustic Emission. [PDF]

Materials (Basel), 2022
Panasiuk K, Dudzik K.
europepmc   +1 more source

Piezoresistive Monitoring of Carbon Nanomaterial‐Reinforced Epoxy Composites Under Cyclic and Fatigue Loading: A Review

Advanced Engineering Materials, EarlyView.
Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares carbon nanotube and graphene systems, correlating filler content, percolation threshold, and gauge factor with sensing stability and damage evolution.
J. M. Parente, J. Nunes‐Pereira, A. P. Silva, P. N. B. Reis   +3 more
wiley   +1 more source

3D‐Printed Giant Magnetoresistive (GMR) Sensors Based on Self Compliant Springs

Advanced Engineering Materials, EarlyView.
This work explores 3D‐printed GMR sensors utilizing self‐compliant spring structures and conductive PLA composites. By optimizing arm width, we achieved high piezoresistive (0.34%/mm) and magnetoresistive (0.77%/mT) sensitivities. Demonstrated through Bluetooth‐integrated pressure and magnetic position sensing, these full printed low‐cost, customizable
Josu Fernández Maestu, Nelson Pereira, Javier Vicente, Carmen Rial Tubio, Senentxu Lanceros‐Méndez   +4 more
wiley   +1 more source

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source