Results 71 to 80 of about 2,592,376 (192)

ASSIMILATION OF PRODUCTION OF THERMO-MECHANICALLY HARDENED REINFORCING BAR WITH EFFECTIVE AND ECONOMICAL CUT, EQUIVALENT DIAMETER 5,5—8,0 mm and 500 H/mm2

Литьë и металлургия, 2005
The carried out team-work of NIIZHB and RUP “BMZ” enabled to receive new technological decisions at production of bale reinforcing bar, realization of which will increase reliability of reinforced-concrete constructions of buildings and installations.
V. A. Matochkin, V. V. Savinkov, A. V. Gontaij, V. I. Shcherbakov   +3 more
doaj  

METAL DEPOSIT OF SLUGS AND PLATES OF CRYSTALLIZERS

Литьë и металлургия, 2006
The new technology of double protective galvanic coat was developed on the basis of investigations of protective coats of muffs and crystallizers plates for sorted and bloom MNLZ and applying of this coat on muffs and crystallizers plates in conditions ...
A. V. Demin, S. M. Borshchev, V. A. Nikolaev, I. V. Gorevoj   +3 more
doaj  

TECHNOLOGY OF PRODUCTION OF HIGH-STRENGTH REINFORCING STEEL

Литьë и металлургия, 2004
The technology of the high-strength spiral hardware is considered in the article. The offered technology allows to bring the mechanical characteristics of high-strength reinforcing steel to conformity with the requirements of practically all the well ...
A. N. Bondarenko, V. I. Shcherbakov, G. L. Bobrenok, A. E. Chernov   +3 more
doaj  

Rolling out defects during rolling of castings at the mill 850 of Belarussian metallurgical plant

Литьë и металлургия, 2001
Results of industrial experiment are given and regularities of rolling out of surface defects of artificial origin are investigated at rolling of continuous castings at the rolling mill 850 of Belarussian metallurgical ...
V. I. Scherbakov, V. V. Filippov, V. A. Tischenko, M. I. Titov   +3 more
doaj  

A model of management teams [PDF]

Management;Decision ...
Ley, E., Steel, M.F.J.
core   +1 more source

IMPROVEMENT OF THERMOSTRENGTHENING MODE OF VALVE № 14, 16 CLASS 500 IN SMALL SECTION MILL 320 OF «BSW

Литьë и металлургия, 2012
Advanced mode of valves № 14, 16 500 class thermostrengthening, allowed to increase the productivity of the mill 320 without degradation of mechanical properties, reduce the energy used to produce steel.
М. A. Murikov, N. A. Bobkov, A. V. Gordienko, A. V. Rusalenko   +3 more
doaj  

DEVELOPMENT AND CURRENT STATUS OF THE INTERNAL SETTLEMENT AT RUP “BMZ”

Литьë и металлургия, 2008
New main stages of development of the internal settlement system at RUP ''BMZ” are ...
A. E. Nikiforov, A. V. Volkov, V. E. Sidorchuk, A. V. Voitovich   +3 more
doaj  

TECHNOLOGICAL PECULIARITIES O F MELTING AND OUT-OF-FURNACE PROCESSING OF BALANCED STEELS IN CONDITIONS OF ELECTRIC FURNACE STEELMAKING AND CONTINUOUS CASTING

Литьë и металлургия, 2007
The technological peculiarities of melting and out-of-furnace processing of balanced steels in conditions of electric furnace steelmaking and continuous cast of RUP “BMZ” are considered.
S. V. Terletski, V. V. Pivtsajev, A. V. Olenchenko, A. S. Zazjan   +3 more
doaj  

ADHESION OF RUBBER TO METAL CORD AND ITS PTESETVATION

Литьë и металлургия, 2005
It is shown that the correct selection of lubricant for wiredrawing allows not only to improve the technological characteristics of wire for the steel wire cord spin but to guarantee the stability of adhesion characteristics of steel wire cord as well.
N. V. Andrianov, A. N. Savenok, A. A. Kravtsov, A. A. Ledneva   +3 more
doaj  

ENERGY ECONOMICAL ASPECTS OF THE HEATING FURNACES WORKING

Литьë и металлургия, 2005
It is shown that for realization of the balance ''high effectiveness - low level of discharge'' the complex of actions is required, as increasing of one of the indices of the balance always results in decreasing of the other one.
I. V. Kotov, V. A. Matochkin, A. A. Sotnikov, E. V. Bobrova   +3 more
doaj