Results 41 to 50 of about 14,200 (259)
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A novel workflow for investigating hydride vapor phase epitaxy for GaN bulk crystal growth is proposed. It combines Design of experiments (DoE) with physical simulations of mass transport and crystal growth kinetics, serving as an intermediate step between DoE and experiments.
J. Tomkovič +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley +1 more source
Stick-Slip Transition at the Nanometer Scale
Physical Review Letters, 2003 We report the first observation of a stick-slip transition of surfactant solution flow through nanopores. From the experimental data, we were able to determine both the slip length and the critical wall shear stress from which slip occurs. Whereas the latter is found to increase linearly with the concentration, the former remains constant and ...
Cheikh, C. (author), Koper, G. (author)
openaire +4 more sources
Advanced Engineering Materials, EarlyView.Dislocation cutting of γ′ precipitates in Ni‐based superalloys is investigated by linking atomistic simulations with discrete dislocation dynamics. The critical cutting stress is shown to be governed by the antiphase boundary energy, while line tension effects promote edge‐preferred cutting.
Frédéric Houllé +9 more
wiley +1 more source
Design and Experimental Research of a Novel Stick-Slip Type Piezoelectric Actuator [PDF]
Micromachines, 2017 Di Wu, Zhichao Ma, Kun Hong
exaly +1 more source
Advanced Engineering Materials, EarlyView.A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Research on Stick-slip Vibration Level Estimation of Drillstring Based on SVM
Shiyou jixie, 2019 To evaluate the severity of stick-slip vibration of drill string, a risk assessment method based on factor analysis (FA) and support vector machine (SVM) is proposed.
Chen Chong +4 more
doaj
Development of surface dynamic mechanical analysis tests for TPU materials [PDF]
FME Transactions, 2010 The stick-slip behaviour of elastomers plays an extremely important role under service relevant loading conditions in many tribological applications. In a number of practical situations, the friction instability (stick-slip) causes negative influence on ...
Hausberger Andreas +3 more
doaj