Results 41 to 50 of about 2,503 (249)

Experimental Investigation on the Fatigue Life of Ti-6Al-4V Treated by Vibratory Stress Relief

Metals, 2017
Vibratory stress relief (VSR) is a highly efficient and low-energy consumption method to relieve and homogenize residual stresses in materials. Thus, the effect of VSR on the fatigue life should be determined. Standard fatigue specimens are fabricated to
Han-Jun Gao, Yi-Du Zhang, Qiong Wu, Jing Song   +3 more
doaj   +1 more source

Pyramidal Structures on Yttria‐Stabilized Zirconia after High Temperature Exposure at 1500°C: New Features on an Old Material

Advanced Engineering Materials, EarlyView.
New features on yttria‐stabilized zirconia after exposure at 1500°C: Newly discovered pyramidal structures on an old material. After exposure at 1550°C on the cross section of YSZ new features, namely pyramidal structures are discovered. These structures grow with time, increase in numbers, appear as singularities, are often arranged in strings, and ...
Doris Sebold, Dylan Jennings, Robert Vaßen   +2 more
wiley   +1 more source

Influence of Bending Cold Working Process on Properties of Clod Rolling Non-Oriented Silicon Steel

Teshugang, 2020
The microstructures and textures in final products of the non-oriented silicon steel(0.003% C,0.80% Si, 0. 28%Mn,0. 015%P,0. 003%S,0. 24% Als) with different cold bending process and stress-relief annealing at 750 °C for 2h are determined and analyzed ...
张智义, 李亚东, 陈春梅, 高振宇, 刘文鹏, 毛卫民, 杨平   +6 more
doaj  

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Microstructure and mechanical properties of a modified 316 austenitic stainless steel alloy manufactured by laser powder bed fusion

Journal of Materials Research and Technology
A 316 austenitic stainless-steel alloy, with modified alloy composition, manufactured by laser powder bed fusion (L-PBF) has been investigated. The modification of the alloy composition included addition of niobium (Nb), tungsten (W) and copper (Cu ...
F. Svahn, P. Mishra, E. Edin, P. Åkerfeldt, M.-L. Antti   +4 more
doaj   +1 more source

The effect of structural changes on the functional properties of Fe65.5Cr4Mo4Ga4P12C5B5.5 bulk metallic glass [PDF]

Serbian Journal of Electrical Engineering
The ferromagnetic Fe65.5Cr4Mo4Ga4P12C5B5.5 bulk metallic glass rods of 1.8 mm diameter were prepared prepared by the copper-mold casting technique. As-quenched and successive furnace annealed samples were examined by thermal analysis (DTA), X ...
Mitrović Nebojša, Čukić Bratislav, Nedeljković Borivoje, Kalezić-Glišović Aleksandra, Obradović Nina   +4 more
doaj   +1 more source

Influence of Stress Relief Annealing Parameters on Mechanical Properties and Decomposition of Eutectic Si Network of L-PBF Additive Manufactured Alloy AlSi10Mg

Metals, 2022
This paper evaluates the effect of stress-relieving heat treatment on the AlSi10Mg alloy prepared by additive manufacturing using the Laser Powder Bed Fusion (L-PBF) with print parameters: 370 W, 1400 m/s, and 50 μm. The as-built state and four different
Ludmila Růžičková, Jana Sobotová, Libor Beránek, Lukáš Pelikán, Jan Šimota   +4 more
doaj   +1 more source

Versatile Pneumatic Twisted Coiled Actuators Enabled by Fiber‐Polymer Composite Fabrication

Advanced Functional Materials, EarlyView.
This work reports composite Pneumatic Twisted Coiled Actuators with embedded Kevlar fibers that convert pneumatic or hydraulic pressure into powerful linear motion. A novel precise manufacturing technique is used to systematically explore how design variables influence actuator mechanics and dynamics.
William J. Townsend, Jeongmin Kim, Samuel Tsai, Yichao Shi, Sameh Tawfick, James H. Pikul   +5 more
wiley   +1 more source

Make‐Use‐Remake: Toward Indefinite Low‐Temperature Material Loops

Advanced Functional Materials, EarlyView.
We introduce a regenerable materials platform built from microparticles bound by a temperature‐responsive polymer shell, enabling strong, processable structures from diverse feedstocks. The material is shaped at low temperatures (80°C) using common manufacturing methods and reprocessed repeatedly in the presence of water, demonstrating stable ...
Nikola Křivánková, Wouter van der Wijngaart, Ulrica Edlund   +2 more
wiley   +1 more source

Self‐Assembled Monolayers in p–i–n Perovskite Solar Cells: Molecular Design, Interfacial Engineering, and Machine Learning–Accelerated Material Discovery

Advanced Materials, EarlyView.
This review highlights the role of self‐assembled monolayers (SAMs) in perovskite solar cells, covering molecular engineering, multifunctional interface regulation, machine learning (ML) accelerated discovery, advanced device architectures, and pathways toward scalable fabrication and commercialization for high‐efficiency and stable single‐junction and
Asmat Ullah, Ying Luo, Stefaan De Wolf
wiley   +1 more source