Results 71 to 80 of about 9,885 (195)

Comparison and combination of several stress relief methods for cubic boron nitride films deposited by ion beam assisted deposition

, 2009
Cubic boron nitride (c-BN) films were prepared by ion beam assisted deposition (IBAD) technique, and the stresses were primary estimated by measuring the frequency shifts in the infrared-absorption peaks of c-BN samples.
Chen NF, Zhang XW, You JB, Tan HR, Zhang XW Chinese Acad Sci Inst Semicond Key Lab Semicond Mat Sci Beijing 100083 Peoples R China. E-mail Address: xwzhang@semi.ac.cn, Fan YM   +5 more
core  

Investigation of residual stress influence on fatigue crack growth in remanufactured titanium alloy with inhomogeneous microstructure

Journal of Materials Research and Technology
Laser remanufacturing technology is now the top choice for remanufacturing key components of aero-engines because of its cost-effectiveness, resource utilization, and performance recovery.
Xiaohong Zhan, Wanli Ling, Xiaoping Wang, Qiyu Gao, Lijun Liu   +4 more
doaj   +1 more source

Stress reduction and bond stability during thermal annealing of tetrahedral amorphous carbon

, 1999
A comprehensive study of the stress release and structural changes caused by postdeposition thermal annealing of tetrahedral amorphous carbon (ta-C) on Si has been carried out.
Kleinsorge, B, Hart, A, Robertson, J, Morrison, NA, Stolojan, V, ,, Ferrari, AC   +6 more
core  

Fe75 xCoxCu1Nb3Si15B6 Alloy with Rapid Stress Annealing

, 2017
This Articler reports the effect of stress annealing treatment on the structural and magnetic properties of nanocrystalline Fe75 xCoxCu1Nb3Si15B6 and Co21Fe64 xNbxB15 alloys. Information obtained from magnetic measurements, X ray diffraction measurements
Shailendra Singh Khinchi
core   +1 more source

Studi Eksperimental Pengaruh Perlakuan Panas Annealing, Quenching Dengan Media Air Dan Stress Relief Terhadap Kekuatan, Kekerasan Dan Struktur Mikro Tube Condenser CP-Ti Grade 2 [PDF]

, 2015
Commercial Pure Titanium Grade 2 (CP-Ti) digunakan sebagai tube condenser PLTU Paiton. CP Ti Grade 2 dipilih sebagai tube condenser karena memiliki keunggulan pada kombinasi sifat mekanik seperti massa jenis yang lebih rendah, kekuatan yang lebih ...
Nadila, Safira Dina
core  

Elimination of Low-Angle Grain Boundary Networks in FeCrAl Alloys with the Electron Wind Force at a Low Temperature

Metals
Low-angle grain boundaries (LAGBs) accommodate residual stress through the rearrangement and accumulation of dislocations during cold rolling. This study presents an electron wind force-based annealing approach to recover cold-rolling induced residual ...
Md Hafijur Rahman, Sarah Todaro, Luke Warner, Daudi Waryoba, Aman Haque   +4 more
doaj   +1 more source

Mechanical and Structural Responses of Low Carbon Steel to Cold Rolling and Stress Relief Anneal Treatments

Arid Zone Journal of Engineering, Technology and Environment, 2020
This study investigated the effect of deformation by cold rolling and stress relief anneal on the mechanical and structural properties of low carbon steel. The as-received steel samples were cold rolled at 20% – 40% degrees of deformation using Buhler rolling machine in Metallurgical and Materials engineering department University of Lagos, Nigeria ...
Bodude, M. A., Ayoola, W. A., Oyetunji, A.   +2 more
openaire   +2 more sources

On Microstructure Evolution and Magnetic Properties of Annealed FeNiCrMn Alloy

Metals
Fe-Ni-based alloys have attracted attention due to their potential for applications such as transmission line de-icing, where the core requirements include a Curie temperature near the freezing point and sufficient saturation magnetization.
Yu Zhang, Caili Ma, Jingwen Gao, Wenjie Chen, Song Zhang, Xia Huang   +5 more
doaj   +1 more source

Influence of Stress Relief Annealing on the Hardness and Sliding Wear of Invar and Invar-10wt%TiC Manufactured by Laser Powder Bed Fusion

958965This study investigates the influence of TiC addition to Invar manufactured using laser powder bed fusion. Stress relief annealing was performed to relieve residual stresses induced during the LPBF process.
Sacks, Natasha, Oyedeji, Ayodeji Nathaniel, Venter, Andrew M., Pötschke, Johannes, Marais, Deon   +4 more
core   +1 more source

Influence of Partial Er Substitution for Sc on the Microstructure, Mechanical Properties and Corrosion Resistance of Short-Processed Al-4.7Mg-0.6Mn-0.3Zr-0.3Sc Sheets

Metals
Standard AA5083 (ZSE000), AA5083 modified with 0.3 wt.% Zr and 0.3wt.% Sc (ZSE330) and AA5083 modified with 0.3 wt.% Zr, 0.2wt.% Sc and 0.1wt.%Er(ZSE321) sheets were fabricated through a short process (including a simulated twin-belt continuous casting ...
Guangxi Lu, Yabo Liang, Cong Xu, Wenfei Rao, Yaodong Xue, Longfei Li, Li Zhang, Shaokang Guan   +7 more
doaj   +1 more source