Results 41 to 50 of about 8,904 (229)
Bubble Sliding Characteristics and Dynamics of R134a during Subcooled Boiling Flow in a Narrow Gap
Mathematics, 2023 The numerical method was used to study bubble sliding characteristics and dynamics of R134a during subcooled flow boiling in a narrow gap. In the numerical method, the volume of fraction (VOF) model, level set method, Lee phase change model and the SST k
Bo Yu +5 more
doaj +1 more source
Subcooled Boiling Near a Heated Wall [PDF]
, 2000 Experimental measurements of void fraction, bubble frequency, and velocity are obtained in subcooled R-134a flowing over a heated flat plate near an unheated wall and compared to analytical predictions. The measurements were obtained for a fixed system pressure and mass flow rate (P = 2.4 MPa and w = 106 kg/hr) at various inlet liquid temperatures ...
Trabold, T. A. +3 more
openaire +2 more sources
A Methodology to Integrate Closed‐Cycle Heat Pumps into Batch Distillation Columns
Chemie Ingenieur Technik, EarlyView.Batch distillation often cannot use vapor recompression due to contamination risks in food and pharma. This study proposes a design for integrating closed‐loop heat pumps using natural fluids. Results show significant energy savings, offering a sustainable alternative to traditional setups.
Philipp Dorn +5 more
wiley +1 more source
CFD SIMULATION OF UPWARD SUBCOOLED BOILING FLOW OF FREON R12
Acta Polytechnica CTU Proceedings, 2016 Subcooled flow boiling under forced convection occurs in many industrial applications of purpose to maximize heat removal from the heat source by the very large heat transfer coefficient. This work deals with CFD simulations of the subcooled flow boiling
Tomas Romsy, Pavel Zacha
doaj +1 more source
Saturated Critical Heat Flux in a Multi-Microchannel Heat Sink Fed by a Split Flow System [PDF]
, 2010 An extensive experimental campaign has been carried out for the measurement of saturated critical heat flux in a multi-microchannel copper heat sink. The heat sink was formed by 29 parallel channels that were 199 μm wide and 756 μm deep.
D. Toto +3 more
core +1 more source
A Short‐Cut Design Approach to Evaluate Reboiler Designs in Vapor Recompression Scenarios
Chemie Ingenieur Technik, EarlyView.A short‐cut model framework that incorporates mechanical vapor recompression (MVR) requirements into reboiler design is presented, which is particularly beneficial during early process development with limited data or initial feasibility assessments.
Franziska Lais +2 more
wiley +1 more source
Forced boiling of nanofluids, effects of contact angle and surface wettability [PDF]
, 2011 This paper was presented at the 3rd Micro and Nano Flows Conference (MNF2011), which was held at the Makedonia Palace Hotel, Thessaloniki in Greece.
3rd Micro and Nano Flows Conference (MNF2011) +4 more
core
Quench cooling under reduced gravity
, 2013 We report the quench cooling experiments performed with liquid O2 under different levels of gravity simulated with the magnetic gravity compensation. A copper disk is quenched from 270K to 90K.
Beysens, D. +3 more
core +3 more sources
Chemie Ingenieur Technik, EarlyView.Mechanical vapor recompression integration in distillation is analyzed, focusing on feed preheating and column pressure drop. Binary methanol–water and benzene–toluene separations are studied to identify optimal designs, which are further assessed in a bioethanol vacuum distillation sequence regarding energetic, ecological, and economic performance ...
Thorben Hochhaus +3 more
wiley +1 more source
Accuracy Analysis of Bubble-layer-based Model Applied on Rectangular Channel
Yuanzineng kexue jishuSubcooled flow boiling contains complex bubble behaviors and interactions. Accurate prediction and analysis of the subcooled flow boiling are of great significance for the safe operation and economy of the nuclear reactors.
HE Wen, ZHAO Chenru, HAN Jinyu, BO Hanliang
doaj +1 more source