Results 111 to 120 of about 1,780,646 (296)

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control

Advanced Engineering Materials, EarlyView.
This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian, Frédéric Demoly, Mohammad Lakhi, Bernard Rolfe, Mahdi Bodaghi   +4 more
wiley   +1 more source

PROSPECTS OF SOLAR SALT PONDS APPLICATION FOR PRODUCTION OF HEAT AND ELECTRICITY IN THE STAVROPOL REGION

Вестник Северо-Кавказского федерального университета, 2022
The principle of solar salt ponds functioning and characteristics of climate in Stavropol is discribed. Possibility of such ponds application for the production of heat and electricity in the Stavropol region is considered.
Vladislav Vladimirovich Bogachev, Sergey Valer’evich Buslov   +1 more
doaj  

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

Impact of Textile Architecture on the Electromechanical Behavior of Conductive Carbon: Silicone Composite Strain Sensors

Advanced Engineering Materials, EarlyView.
A stretchable carbon composite is integrated by stencil printing onto two different types of textile, with different yarn morphologies. The impact of the knit structure and coating direction on the performance of the sensor composite is evaluated and used to derive a model estimating nominal resistance at a given strain near the percolation threshold ...
Gabriela Ananieva, Giulia Spallanzani, Peter Zalar   +2 more
wiley   +1 more source

Temperature Field and Temperature Effects for Concrete Box Girder Bridges Based on Monitoring Data and Numerical Simulation

Sensors
The temperature field distribution and temperature effects of concrete box girder bridges were found to be critical to their long-term service safety. Based on long-term structural health monitoring data, the temperature field and temperature effects of ...
Mengxiang Zhai, Hongyin Yang, Bin Li, Jing Hao, Weihua Zhou, Hongyou Cao, Zhangjun Liu   +6 more
doaj   +1 more source

Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy

Advanced Engineering Materials, EarlyView.
An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Understanding the Effect of Resistance Temperature Detector Temperature Controllers on Microstructural Alignment in Magnetic Freeze Casting

Advanced Engineering Materials, EarlyView.
The effect of temperature controllers that are commonly used in freeze‐casting is investigated in this work. Temperature controllers are observed to generate a voltage in the slurry. Microstructural alignment and ultimate compressive strength data show this voltage to interfere with the ability to align the microstructure using magnetic fields ...
Maddie A. Schmitz, Steven E. Naleway
wiley   +1 more source

Thermal Effects on Main Girders During Construction of Composite Cable-Stayed Bridges Based on Monitoring Data

Buildings
Thermal effects critically influence the design and construction of steel-concrete composite cable-stayed bridges, where material thermal mismatch complicates structural responses.
Hua Luo, Wan Wu, Qincong She, Bin Li, Chen Yang, Yahua Pan   +5 more
doaj   +1 more source