Results 271 to 280 of about 7,486,347 (328)
Efficient optimization accelerator framework for multi-state spin Ising problems. [PDF]
Nat CommunGarg C, Salahuddin S.
europepmc +1 more source
Magnetic Properties and Corrosion Resistance of Sintered Nd-Fe-B Magnet Caused by Er<sub>69</sub>Fe<sub>31</sub> Alloy Grain Boundary Addition. [PDF]
Materials (Basel)Dai Y +5 more
europepmc +1 more source
Effect of various heat treatment methods and optimization of their parameters on mechanical properties of AISI 4140 steel. [PDF]
Sci RepMudda S +5 more
europepmc +1 more source
Identification of Factors Leading to Damage of Semi-Elliptical Leaf Springs. [PDF]
Materials (Basel)Stańco M, Kaszuba M, Herbik I.
europepmc +1 more source
Some of the next articles are maybe not open access.
Related searches:
Related searches:
Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing, 2018
Abstract The influence of intercritical tempering temperature on impact toughness of quenched and tempered 0.05C-5.42Mn medium-Mn steel was studied and compared with traditional tempering. The experimental steel had high hardenability because of high Mn-content.
R D K Misra
exaly +3 more sources
Abstract The influence of intercritical tempering temperature on impact toughness of quenched and tempered 0.05C-5.42Mn medium-Mn steel was studied and compared with traditional tempering. The experimental steel had high hardenability because of high Mn-content.
R D K Misra
exaly +3 more sources
Journal of Iron and Steel Research International, 2021
Instead of conventional quenching and tempering, fast austenitization from an initial microstructure of lamellar pearlite followed by quenching and tempering was carried out, leading to the formation of inhomogeneous microstructure. It comprised different morphologies of lath martensite and retained austenite (RA).
De-zhen Yang +5 more
openaire +2 more sources
Instead of conventional quenching and tempering, fast austenitization from an initial microstructure of lamellar pearlite followed by quenching and tempering was carried out, leading to the formation of inhomogeneous microstructure. It comprised different morphologies of lath martensite and retained austenite (RA).
De-zhen Yang +5 more
openaire +2 more sources
Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing, 2021
F C Zhang, Ricardo Branco, X Y Long
exaly +2 more sources
F C Zhang, Ricardo Branco, X Y Long
exaly +2 more sources
Materialpruefung/Materials Testing, 2022
The AISI 4140 and AISI 4340 tempered steels are widely used in industry. This study investigated the effects of the tempering temperature on the mechanical properties of these steels. The steels were kept at 850 °C for 30 min, left in an oil environment,
Nursel Altan Özbek
exaly +2 more sources
The AISI 4140 and AISI 4340 tempered steels are widely used in industry. This study investigated the effects of the tempering temperature on the mechanical properties of these steels. The steels were kept at 850 °C for 30 min, left in an oil environment,
Nursel Altan Özbek
exaly +2 more sources
Effect of deep cryogenic treatment, tempering temperature and time on hardness of Nimonic-90
Proceedings of the Institution of mechanical engineers. Part E, journal of process mechanical engineering, 2023The present study has been done to determine the effect of deep cryogenic treatment (DCT) on the hardness of Nimonic-90. From the study, it has been found that the hardness of the material is significantly affected with cryogenic treatment which includes
Gurkirat Singh, K. Pandey
semanticscholar +1 more source