Results 81 to 90 of about 6,248 (259)
Metals, 2019 T92 heat-resistant steel is among the most promising candidate materials for structural components in the Generation IV (GEN-IV) reactors. The effects of tempering temperature on the microstructure and mechanical properties of the T92 steel were studied.
Dandan Zhao +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Low‐temperature imidization of PEG‐modified polyimide enables fully screen‐printed, roll‐to‐roll fabrication of flexible electrodes on PET substrates, delivering robust mechanical durability and reliable ECG/EMG signal performance for wearable electronics.
Akib Abdullah Khan, Jong‐Hoon Kim
wiley +1 more source
Effect of Heat Treatment on Microstructure and Hardness of 9Cr13Mo3Co3Nb2V Steel
Journal of Aeronautical Materials, 2016 Effect of heat treatment on the microstructure and hardness of 9Cr13Mo3Co3Nb2V steel was studied systematically by metallographic examination and hardness testing.
HUO Dengping, LIANG Zhikai
doaj +1 more source
Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys
Advanced Engineering Materials, EarlyView.This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa +9 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.New features on yttria‐stabilized zirconia after exposure at 1500°C: Newly discovered pyramidal structures on an old material. After exposure at 1550°C on the cross section of YSZ new features, namely pyramidal structures are discovered. These structures grow with time, increase in numbers, appear as singularities, are often arranged in strings, and ...
Doris Sebold +2 more
wiley +1 more source
Teshugang, 2021 In order to study the effect of quenching and tempering treatment on the mechanical property of R4s (22MnCrNiMo) mooring chain steel flash weld zone, the double quenching is carried out at 880 ~ 960℃.
李仲昱 +4 more
doaj
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source
Time‐Dependent Oxidation and Scale Evolution of a Wrought Co/Ni‐Based Superalloy
Advanced Engineering Materials, EarlyView.This study shows how a new wrought Co/Ni‐based superalloy resists oxidation at 800 ∘$^\circ$C. The oxide scale changes from rough, fast‐growing spinel to a dense, protective chromia–alumina layer. Atom probe analysis reveals tiny refractory‐rich bubbles at the interface that mark the transition to long‐term, diffusion‐controlled protection ...
Cameron Crabb +6 more
wiley +1 more source
Jixie qiangduObjectiveAims to investigate the lack of test data and microscopic mechanism analysis of 60Si2CrV spring steel under high-temperature tempering.
FENG Yonghua +8 more
doaj
Karl Popper and the Mechanisms of Hydrogen Embrittlement
Advanced Engineering Materials, EarlyView.Representation of the beginning of loss of ductility rather than embrittlement. Small concentrations of hydrogen in a diffusible form within iron are well‐established to harm the mechanical integrity of steels. There are theories that attempt to explain the pernicious role of hydrogen.
H. K. D. H. Bhadeshia
wiley +1 more source