Results 1 to 10 of about 6,411,821 (351)

Effect of thermal cycling and hydro‐thermal cycling on physical and mechanical properties of sandstone [PDF]

Energy Science & Engineering, 2020
Thermal storage of sandstone is widely distributed in sedimentary basins in China with a very high degree of exploitation and utilization, while the low recharge rate is the bottleneck of its sustainable development.
Pengfei Liu, Xingfei Liu, Guodong Tian, Fei Gan, Jing Bi   +4 more
doaj   +4 more sources

Effect of thermal cycling on the mechanical properties of conventional, milled, and 3D-printed base resin materials: a comparative in vitro study [PDF]

PeerJ
Purpose The purpose of this study is to evaluate the impact of thermal cycling on the mechanical properties of conventional, milled, and 3D-printed denture base materials.
Shuang Xiao, Ruo-Jin Zhang, Fa-Bing Tan
doaj   +3 more sources

Effects of confined thermal cycling on sealants with different thermomechanical properties for CCS [PDF]

Scientific Reports
In geological CO2 storage, the integrity of seals between well and caprock is crucial for ensuring permanent CO2 storage. One key mechanism that might affect this integrity is thermal cycling when cold CO2 is injected periodically into a hot reservoir ...
Kai Li, Reinier van Noort, Anne Pluymakers   +2 more
doaj   +2 more sources

Thermal properties and thermal cycling stability of graphite/copper composite fabricated by microwave sintering

Journal of Materials Research and Technology, 2022
Herein, graphite/copper (Gr/Cu) composites were fabricated by mechanical mixing and microwave sintering to investigate the effect of graphite volume fraction on the thermal conductivity (TC) and coefficient of thermal expansion (CTE) of the Gr/Cu ...
Zemin Wang, Zhimeng Tang, Lei Xu, Zhaohui Han, Jianhua Liu, Libo Zhang   +5 more
doaj   +1 more source

Optimization by Thermal Cycling [PDF]

Physical Review Letters, 1997
An optimization algorithm is presented which consists of cyclically heating and quenching by Metropolis and local search procedures, respectively. It works particularly well when it is applied to an archive of samples instead of to a single one. We demonstrate for the traveling salesman problem that this algorithm is far more efficient than usual ...
Fachat, A., Schreiber, M., Fachat, A., Hoffmann, K., Díaz-Sánchez, A., Neklioudov, A., Möbius, A., Schreiber, M., Hoffmann, K., Diaz-Sanchez, A., Neklioudov, A., Mobius, A.   +11 more
openaire   +2 more sources

OPTIMIZATION BY THERMAL CYCLING [PDF]

Complexity, Metastability and Nonextensivity, 2005
Submitted to Proceedings of the Workshop "Complexity, Metastability and Nonextensivity", held in Erice 20-26 July 2004.
Mobius, A., Hoffmann, K. H., Schon, C.
openaire   +2 more sources

Packing grains by thermal cycling [PDF]

Nature, 2006
7 pages, 1 ...
Chen, K., Cole, J., Conger, C., Draskovic, J., Lohr, M., Klein, K., Scheidemantel, T., Schiffer, P.   +7 more
openaire   +2 more sources

Optimization and benchmarking of the thermal cycling algorithm [PDF]

Physical Review E, 2021
8 pages, 5 figures, 1 ...
Amin Barzegar, Anuj Kankani, Salvatore Mandrà, Helmut G. Katzgraber   +3 more
openaire   +4 more sources

Failure mechanism of parallel gap resistance welding joint between Ag foil and GaAs solar cell by temperature cycling

Journal of Materials Research and Technology, 2023
Reliability of joints in solar arrays significantly influences the service life of satellites. Interface between solar cell and interconnector experiences serious temperature cycling during space service which would further lead to failure.
Yuhan Ding, Xiaoran Li, Chen Shen, Ye Huang, Yi Wei, Nannan Chen, Min Wang, Lin Wang, Xunchun Wang, Yan Cai, Bin Qian, Xueming Hua   +11 more
doaj   +1 more source

Effect of cryogenic-thermal cycling treatment on tribological properties of Ti-based amorphous alloy

Cailiao gongcheng, 2022
The wear resistance of titanium alloy is poor, the preparation of amorphous alloy coating on the surface of titanium alloy moving parts is a choice to maintain the advantages of titanium alloy and improve its wear resistance.
DUAN Jun, JI Xiulin, JIN Juan, YAN Chunyan, FU Li   +4 more
doaj   +1 more source