Results 111 to 120 of about 24,682,132 (307)

Reverse design of nickel-based superalloys based on thermodynamic calculation and machine learning

Cailiao gongcheng
The combination of thermodynamic calculation and machine learning was used to reverse design nickel-based superalloys for thermodynamic performance requirements.
ZHU Yaliang, YONG Wei, YANG Jie, WANG Xiaofeng   +3 more
doaj   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

A Study of Phase Equilibrium Of H2S in Several Physical Solvents Using Chemcad Simulator

Tikrit Journal of Engineering Sciences, 2008
CHEMCAD process simulator was used for the analysis of the literature experimental phase equilibrium data of H2S with three physical solvents (Sulfolane, Propylene Carbonate (PC), and N-Methyl-2-Pyrrolidone (NMP)) at different temperatures ( 298.15 oK ...
Zaid A. Abdel-Rahman
doaj   +1 more source

Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)

Advanced Engineering Materials, EarlyView.
Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho, M. Naeem, T. H. C. Costa, M. S. Libório, J. C. A. Queiroz, C. B. B. Luna, R. R. M. Sousa, P. S. Vieira, E. M. Araújo   +8 more
wiley   +1 more source

Exploration of Pseudobinary Alloys (Al–Mn)‐(Co–Fe–Ni) to Design High‐Entropy and Compositionally Complex Alloys to Stabilize the τ Phase in Al–Mn‐Based Ferromagnetic Alloys

Advanced Engineering Materials, EarlyView.
This experimental study investigates the thermodynamic limits of the Al–Mn τ ferromagnetic phase within complex‐composition alloys (CCAs). Using nine rare‐earth‐free compositions, it explores a broad region of the pseudobinary AlMnCoFeNi system. The results reveal intricate links between composition, phase stability, and magnetic behavior, highlighting
Sacha Plagnol‐Chauzu, Laurent Peltier, Fodil Meraghni, Stéphane Delalande, Frédéric Mazaleyrat   +4 more
wiley   +1 more source

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

Reduced-Order Thermodynamic Models for Servo-Pneumatic Actuator Chambers

, 2006
This paper discusses thermodynamic models of air inside pneumatic actuator chambers. In servo-pneumatics common practice, these models are simplified by neglecting the temperature dynamics. Classical models in the literature assume the temperature inside
J. Carneiro, F. G. de Almeida
semanticscholar   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Triple Junctions as Dislocation‐Like Defects: The Role of Grain Boundary Crystallography Revealed by Experiment and Atomistic Simulation

Advanced Engineering Materials, EarlyView.
Grain boundary triple junctions are an essential ingredient of the microstructure of polycrystalline materials. In this study, a triple junction is observed using atomic‐resolution scanning transmission electron microscopy and characterized. Computer simulations reveal that the junction has a dislocation character that is determined by the joining ...
Tobias Brink, Saba Saood, Peter Schweizer, Jörg Neugebauer, Gerhard Dehm   +4 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source