Results 241 to 250 of about 13,658,456 (395)

Thermomechanical pressing and immediate quenching: enhanced piezoelectricity and transparency in piezoelectric nanofibers. [PDF]

Nat Commun
Qu Z, Chen Q, Li X, Liu J, Lang C, Xu Y, Tang R, Zhang J, Wang H, Du Y, Lin T, Fang J.   +11 more
europepmc   +1 more source

CENTRIFUGAL CASTING–SHS PROCESS OF THE CAST CoCrFeNiMn- TYPE HIGH-ENTROPY ALLOY HARDENED BY THERMOMECHANICAL TREATMENT AND THE INTRODUCTION OF SILICON–BORIDE HARDENERS

, 2019
В. Н. Санин, Д. М. Икорников, О. А. Голосова, Д. Е. Андреев, V. I. Yukhvid, Sergey Zherebtsov   +5 more
openalex   +1 more source

Influence of Viscous Dissipation on Wear Behavior and Hardness Evolution of Tool Steels in Glass‐Fiber‐Reinforced Polymer Processing

steel research international, EarlyView.
Tool steels tested under injection molding conditions with glass‐fiber‐reinforced polymers, revealing how viscous dissipation drives hardness loss, even in PM grades. A sharp rise in wear with increasing injection volume rate and thermomechanical load uncovers striking material differences.
David Zidar, Roman Staudigl, Walter Friesenbichler, Clemens Holzer   +3 more
wiley   +1 more source

Tailoring the Mechanical Properties of Al_0.4CrFe₂Ni₂ Medium-Entropy Alloy via Thermomechanical Processing. [PDF]

Materials (Basel)
Kočiško R, Petroušek P, Milkovič O, Diko P, Girman V, Sütőová A, Duchek M, Zemko M.   +7 more
europepmc   +1 more source

Alloy Qualification for Producing Quench and Tempered Plate Steels with Extra‐Heavy Gage

steel research international, EarlyView.
This study develops alloy concepts for ultraheavy steel plates (>100 mm) with ≥690 MPa yield strength. Through dilatometry and Jominy testing, the effects of Mo, Ni, and B on hardenability are quantified. A synergy between 0.5% Mo and 0.5%–1.0% Ni ensures core strength at low cooling rates, while boron microalloying suppresses ferrite and promotes ...
Xabier Azpeitia, Unai Mayo, Nerea Isasti, Eric Detemple, Hardy Mohrbacher, Pello Uranga   +5 more
wiley   +1 more source

Impact of Thermomechanical Aging on Marginal Fit and Fracture Resistance of CAD/CAM Endocrowns Fabricated from Different Materials. [PDF]

Polymers (Basel)
Tartuk BK, Akın Tartuk G.
europepmc   +1 more source

Exploiting Residual Elements Arising from Scrap Steel in Future Sustainable Steel Alloy Design

steel research international, EarlyView.
Herein, the effects of residual elements Cu and Sn on grain growth, recrystallization, and phase transformation in C–Mn steel are summarized, and a case study is presented on how the presence of residual elements can be exploited to reduce deliberate Nb microalloying while achieving the same grain size control and strength during thermomechanical ...
Claire Davis, Carl Slater, Yulin Ju, Jiaqi Duan, Pedram Dastur, Martin Strangwood   +5 more
wiley   +1 more source

Assessment of removal torque values of anodized abutment screws at different voltages: an in vitro study. [PDF]

BMC Oral Health
Arslan Y, Gümüş HÖ, Çolpak ED.
europepmc   +1 more source

Technological parameters optimization of the AlZn5Mg3Cu alloy thermomechanical treatment process

, 2017
Marian NEACŞU, Elena Chiriac, A. Chiriac, Olimpia Pandia, Ion Sărăcin   +4 more
openalex   +1 more source

Two‐Stage Isothermal Transformation of Austenite into Nanobainite in a Chemically Inhomogeneous Medium‐Alloy Steel Containing 0.5 wt% C

steel research international, EarlyView.
The effect of chemical inhomogeneity on the microstructure and properties of nanobainitic steel is investigated. A two‐stage isothermal heat treatment that produced a more uniform microstructure is designed. The first‐stage temperature is higher than the MS of depleted bands; conversely, the second‐stage temperature is lower than the first‐stage ...
Bogdan Garbarz, Jarosław Marcisz, Marek Jelec, Władysław Zalecki, Radosław Rozmus, Zofia Kania‐Pifczyk   +5 more
wiley   +1 more source