Results 21 to 30 of about 363,896 (267)

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur, Faruk Kaya, Bora Derin, Mustafa Lütfi Öveçoğlu, Ju Li, Duygu Ağaoğulları   +5 more
wiley   +1 more source

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Preparation and characterization of suitable insulating and transparent conducting thin films for thin film electroluminescent devices by sol-gel process [PDF]

, 2001
Thin film electroluminescent (TFEL) displays are attractive because they are light, have low power consumption, wide viewing angle and long lifetime, are extremely rugged and can be used in hostile environments.
Alam, Mohammad Jahangir
core  

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

Advanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera, Philippe Marrec, A. Jorge Parola, Madalena Dionísio, Hugo Águas, Andreia F. M. Santos, Hamed Pourkheirollah, Donald Lupo, César A. T. Laia   +8 more
wiley   +1 more source

Giant dielectric permittivity in ferroelectric thin films : domain wall ping pong

, 2015
This study was supported by the National Key Basic Research Program of China (No. 2014CB921004), the National Natural Science Foundation of China (Nos.
Scott, James Floyd, Wei Zhang, D., Seong Hwang, C., Jian Meng, X., Hyuk Park, M., Jin Kim, Y., Quan Jiang, A., Yoo, S.   +7 more
core   +1 more source

Preparation and characterization of the defect–conductivity relationship of Ga-doped ZnO thin films deposited by nonreactive radio-frequency–magnetron sputtering [PDF]

, 2010
Ga-doped ZnO (ZnO:Ga) thin films were prepared by radio-frequency–magnetron sputtering on conventional glass substrates at room temperature. The structural, electrical, and optical properties of these films as a function of argon pressure and film ...
Pasquet, Isabelle, Tailhades, Philippe, J.M. Soon, Ph. Tailhades, Presmanes, Lionel, L. Presmanes, Soon, Jia Mei, A. Barnabé, Barnabé, Antoine, M. Lalanne, Lalanne, Maëva, I. Pasquet   +11 more
core   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Intrinsic photoluminescence Stokes shift in semiconductors demonstrated by thin-film CdS formed with pulsed-laser deposition

, 2014
While not reported in the literature, by employing highly oriented, semi-insulating, thin-film CdS as test material, we present the observation of the intrinsic photoluminescence Stokes shift in a semiconductor.
B., Ullrich, Bhowmick, M., Ariza-Flores, D., Ullrich, B.   +3 more
core   +1 more source