Results 131 to 140 of about 8,331 (256)
Advanced Engineering Materials, EarlyView.This article presents an experimental and numerical modal investigation of composite sandwich structures using surfboards as model systems. By comparing different core materials and reinforcement strategies, the study demonstrates how local stiffeners influence vibrational response and introduce characteristic modal features, highlighting modal ...
Brett Connellan +4 more
wiley +1 more source
Experimental test on 3D-printing components for Architectural Restoration
Fracture and Structural IntegrityThe paper investigates the use of 3D-printed components made from Polylactic Acid (PLA) for the restoration of architectural and ornamental elements, focusing on architectural/structural components.
Valentina Tomei +2 more
doaj +1 more source
Compression bending test for pvc pipe [PDF]
, 2008 In this project the superiority of the compression bending testing method will be demonstrated and compare with other conventional bending test method such as three point bending. Compression bending is a new bending test method. PVC pipe were used as
Wan Ahmad, W.A.A
core
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Nonlinear semi-numeric analysis and simplified analysis of polymer fiber-reinforced concrete prisms under three-point bending test conditions [PDF]
This paper presents a semi-numeric nonlinear analysis and a simplified analysis for evaluating the load-displacement behavior of polymer fiber-reinforced concrete elements under three-point bending test conditions.
Ziga Unuk, Unuk Ziga
core +1 more source
Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method
Advanced Engineering Materials, EarlyView.A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley +1 more source
, 2006 In this work a parametric study of the Edge Crack Torsion (ECT) specimen was performed in order to maximize the mode III component (GIII) of the strain energy release rate for carbon-epoxy laminates.
Morais, A. B. de +3 more
core
, 2020 THE BIOMECHANICAL ANALYSIS FOR BIODEGRADABLE PURE MAGNESIUM BONE SCREWS UNDER THREE POINT BENDING AND TORSIONAL TESTAbstractRecently, magnesium and its alloys have been used as the raw material of degradable implants.
KOVACI, Halim +5 more
core
V-shaped bending support’ membantu dalam eksperimen ‘3-point bending test’ untuk tikus bersaiz kecil (V-shaped bending support helps in 3-point bending test experiment for small mice bone) / Noor Shafini Mohamad and Mohd Hafizi Mahmud [PDF]
, 2020 Three-point bending test is one of the main methods used in long bones to characterise bone material and determine the biomechanical properties. We have examined the mechanical competencies of the mouse bones at four-week-old by using a three-point ...
Mahmud, Mohd Hafizi +1 more
core
Laser‐Induced Graphene from Waste Almond Shells
Advanced Functional Materials, EarlyView.Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova +9 more
wiley +1 more source