Results 121 to 130 of about 32,320 (228)

Influence of Various Implant Placement Strategies on Stress Distribution in Maxillary Implant‐Retained Overdenture: A 3D Finite‐Element Analysis

Clinical and Experimental Dental Research, Volume 12, Issue 1, February 2026.
ABSTRACT Objectives This study used three‐dimensional (3D) finite‐element analysis (FEA) to investigate the effect of different implant placement strategies on the biomechanical behavior of implant‐supported maxillary overdentures, and provide an initial guide to clinical treatment. Materials and Methods For an edentulous maxilla, six different implant‐
Zahra Ghorbani, Ebrahim Shojaei, Hamid Neshandar Asli, Mehran Falahchai   +3 more
wiley   +1 more source

Chip pattern, burr and surface roughness in laser assisted micro milling of Ti6Al4V using micro ball end mill

Journal of Mechanical Engineering and Sciences, 2018
The effectiveness of laser heating could easily fluctuates when the uncut chip thickness are extremely inconsistent. In the case of using micro ball end mill tool, rubbing mechanism is inevitable due to its radial shape geometry.
Z. Mohid, E.A. Rahim
doaj   +1 more source

Finite Element‐Based Wear Prediction Using Archard's Law for Single Mobility Bearing of Total Hip Prosthesis During Walking: A Literature Review

Engineering Reports, Volume 8, Issue 2, February 2026.
This review provides a comprehensive and critical evaluation of computational wear prediction studies in total hip prostheses, with a specific focus on those employing Archard's wear law within finite element frameworks under walking conditions for single mobility bearing designs.
Muhammad Imam Ammarullah, Abdulfatah Abdu Yusuf, Mohamad Izzur Maula, M. Danny Pratama Lamura, Budi Setiyana, Mohammad Tauviqirrahman, Athanasius Priharyoto Bayuseno, Jamari Jamari, Muhammad Hanif Ramlee   +8 more
wiley   +1 more source

Mikro Ark Oksidasyon İşlemi ile Kaplanan Ti6Al4V Alaşımının Yüzey Karakterizasyonu Ve Korozyon Özelliklerinin İncelenmesi

Sakarya Üniversitesi Fen Bilimleri Enstitüsü Dergisi, 2018
Titanyum vealaşımları üstün mekanik özelliklerinden dolayı birçok sektörde tercihedilmekte olup, son yıllarda medikal uygulamalarda daha sık karşımızaçıkmaktadır.
Aysun Ayday
doaj   +1 more source

Comparison of the Dynamic Cut‐Out Failure Modes of Common Proximal Femoral Fixation Devices Using a Mesh‐Free Computational Method

Journal of Orthopaedic Research, Volume 44, Issue 2, February 2026.
Migration and cut‐out of DHS, Gamma3, PFNA‐II, and TFNA were compared under dynamic loading in a stable intertrochanteric fracture benchtop foam model and a mesh‐free simulation. No significant differences in force at cut‐out were observed, but simulation revealed that the volumes of damaged bone foam were 15%, 32%, and 25% higher for the Gamma3, PFNA,
Erica Ueda Boles, Sloan Kulper, Katie Whiffin, Marilyn Janice Oentaryo, Kerstin Schneider, Frankie Leung, Christian X. Fang   +6 more
wiley   +1 more source

Undulator-Based Positron Source at 250 GeV CM Energy with Different Optical Matching Devices: Pulsed Flux Concentrator and Quarter Wave Transformer

, 2018
In the baseline design of the International Linear Collider (ILC) an undulator-based source is foreseen for the positron source. In this study the energy deposition in the pulsed flux concentrator (FC) of positron source is calculated for the ILC at 250 ...
Moortgat-Pick, Gudrid, Riemann, Sabine, Ushakov, Andriy   +2 more
core   +2 more sources

Antimicrobial‐Releasing Implant Substrates for Combating Oral Biofilms: An In Vitro Study

Clinical Oral Implants Research, Volume 37, Issue 2, Page 210-223, February 2026.
ABSTRACT Background and Objectives Peri‐implantitis, a biofilm‐associated inflammatory disease, significantly threatens dental implant longevity. Current treatments face limitations due to biofilm robustness. This study evaluates the efficacy of antimicrobial‐releasing titanium‐silica (Ti/SiO2) composite implant systems against multispecies oral ...
Nur Hidayatul Nazirah Kamarudin, Lars Vanmunster, Brecht Van Hooreweder, Kenneth Siemons, Kristel Bernaerts, Wim Teughels, Annabel Braem, Naiera Zayed   +7 more
wiley   +1 more source

Development of a Four‐Language Questionnaire to Investigate Environmental Risk Factors for the Development of Canine Atopic Dermatitis and to Monitor Disease Course and Progression

Veterinary Dermatology, Volume 37, Issue 1, Page 34-44, February 2026.
Background: The chronic and multifactorial character of canine atopic dermatitis (cAD) often leads to poor disease control and treatment dissatisfaction. Environmental factors are likely to contribute to the disease development and may play a more important role than assumed previously.
Patricia Clara‐Maria Rhodius, Nina Fischer, Ana Rostaher, Franco Martini, Edwin Chapman, Sabrina Audergon, Stefan Hobi, Georg Lehner, Sylvie Wilhelm, Noëmi van Oordt, Claude Favrot, Malwina Kowalska   +11 more
wiley   +1 more source

Positron Source Simulations for ILC 1 TeV Upgrade

, 2013
The generation and capture of polarized positrons at a source with a superconducting helical undulator having 4.3 cm period and 500 GeV electron drive beam have been simulated.
Gai, Wei, Liu, Wanming, Moortgat-Pick, Gudrid, Riemann, Sabine, Ushakov, Andriy   +4 more
core  

Dedicated TEM study from the core structure of adiabatic shear bands in dynamical deformed Ti6Al4V [PDF]

, 2010
Metals and alloys deformed at high strain rates, which are occurring during impact or metal forming situations can suffer from premature failure due to the introduction of so called adiabatic shear bands (ASB).
Coghe, Frederik, Degrieck, Joris, Peirs, Jan, Rabet, Luc, Schryvers, Dominique, Tirry, Wim, Verleysen, Patricia   +6 more
core