Results 21 to 30 of about 353 (132)

Study on Friction and Wear Characteristics of Coating on Surface of WC Cemented Carbide and Its Milling Performance [PDF]

open access: yesCailiao Baohu, 2023
In order to investigate the friction and wear characteristics of nitride coatings on surface of WC cemented carbide and their effect on tool milling performance, TiN, CrN and TiAlN nitride coatings were deposited on surface of WC cemented carbide by ...
SHAO Shu-feng, CHENG Xian-ming, SUN Shou-Yu, YANG Ke, FENG Yuan
doaj   +1 more source

Mechanical properties of multilayer coatings TiAlN

open access: yesJournal of Physics: Conference Series, 2021
Abstract This study aims to examine multilayer TiAlN coatings. The mechanical properties of the coatings were obtained based on micromechanics methods and finite element modeling of a representative volume of a layered medium in ANSYS. Our findings are in line with the data on coating nanoindentation.
V I Kolesnikov, T V Suvorova, O A Belyak
openaire   +1 more source

Research progress in effect of element doping on performance of TiAlN coated cutting tools

open access: yesCailiao gongcheng
With the rapid development of China’s manufacturing industry and the emergence of difficult-to-machine materials, there is an urgent need for cutting technology to continuously update and iterate, and the development of cutting tools has become a key ...
ZHOU Lan   +3 more
doaj   +1 more source

Machining Performance of TiAlN-Coated Cemented Carbide Tools with Chip Groove in Machining Titanium Alloy Ti-6Al-0.6Cr-0.4Fe-0.4Si-0.01B

open access: yesMetals, 2018
In this paper, TiAlN-coated cemented carbide tools with chip groove were used to machine titanium alloy Ti-6Al-0.6Cr-0.4Fe-0.4Si-0.01B under dry conditions in order to investigate the machining performance of this cutting tool.
Zhaojun Ren   +4 more
doaj   +1 more source

Finish machining of hardened steel by face milling using uncoated and TiSiN and TiAlN coated PCBN tools

open access: yesТехнічна інженерія
The article presents the results of experimental studies on the influence of various cutting regimes on the surface roughness of high-hardness hardened steel obtained after face milling with polycrystalline cubic boron nitride (PCBN) tools, both uncoated
Ya.Р. Kovalenko, P.Р. Melnychuk
doaj   +1 more source

Coating-thickness-dependent physical properties and cutting temperature for cutting Inconel 718 with TiAlN coated tools

open access: yesJournal of Advanced Research, 2022
Introduction: Coating-thickness-dependent physical properties can induce different cutting temperatures with physical vapor deposition (PVD) titanium aluminum nitride (TiAlN) ceramic-coated tools.
Jinfu Zhao   +6 more
doaj   +1 more source

DLC Coatings for Manufacturing Applications: Effects of Coating Structure on Mechanical and Tribological Performance

open access: yesLubricants
Adhesion strength, toughness, and resistance to frictional heating are critical characteristics for suppressing premature coating delamination and protecting the substrate from plastic deformation.
Mohd Hafis Sulaiman   +4 more
doaj   +1 more source

Comparative analyses on tool wear in helical milling of Ti-6Al-4V using diamond-coated tool and TiAlN-coated tool

open access: yesJournal of Advanced Mechanical Design, Systems, and Manufacturing, 2014
This paper aims to establish the wear mechanisms of tungsten carbide (WC) tools coated with TiAlN and coated with diamond respectively when helical milling Ti-6Al-4V.
Xuda Qin   +6 more
doaj   +1 more source

Wake‐Up and Fatigue under Electrical Cycling in HfO2‐Based Ferroelectrics: Mechanisms and Strategies toward Reliable Devices

open access: yesAdvanced Science, EarlyView.
HfO2‐based ferroelectrics exhibit wake‐up and fatigue behaviors during electrical cycling, significantly affecting device endurance and reliability. These phenomena are governed by defect dynamics, including oxygen vacancy redistribution and charge trapping.
Hongseok Kim   +6 more
wiley   +1 more source

Cr2O3‐Mediated Phase Transformation and Microstructural Evolution in LDED CuAlMnTi SMA Coatings Toward Resource‐Efficient Wear Protection

open access: yesEcoMat, Volume 8, Issue 11, November 2026.
The Cr2O3‐reinforced CuAlMnTi shape memory alloy coatings were fabricated via laser direct energy deposition. The addition of Cr2O3 refined the microstructure, altered the phase transformation behavior, and improved the high‐temperature tribological performance.
Yuxing Peng   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy