Results 61 to 70 of about 197,858 (305)
Advanced Engineering Materials, EarlyView.Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares carbon nanotube and graphene systems, correlating filler content, percolation threshold, and gauge factor with sensing stability and damage evolution.
J. M. Parente +3 more
wiley +1 more source
Acta Scientiarum: Technology, 2014 The major problem on geotechnical work is to ensure that no settlements occur during the life cycle of the construction. This involves proper design of foundations and their bearing capacity. The Brazilian standard for design and execution of foundations,
Anna S. P. Peixoto, David de Carvalho
doaj +1 more source
Noncontact torque measurement using stroboscopic techniques [PDF]
, 1972 Noncontact torquemeter measures torsional deflection of rotating shaft and results are viewed on vernier scale. Magnitude of torque must be calculated from measured deflection.
Leonard, W. H.
core +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source
Torque Measurement of 3-DOF Haptic Master Operated by Controllable Electrorheological Fluid
Measurement Science Review, 2015 This work presents a torque measurement method of 3-degree-of-freedom (3-DOF) haptic master featuring controllable electrorheological (ER) fluid. In order to reflect the sense of an organ for a surgeon, the ER haptic master which can generate the ...
Oh Jong-Seok +2 more
doaj +1 more source
The opportunities of two-phase hybrid stepping motor back EMF sampling [PDF]
, 2011 By counting the step command pulses, stepping motors can be straightforwardly used for open loop positioning. However, open-loop control is often insufficient to guarantee accurate and energy efficient movements.
Carlier, Lennart +10 more
core +2 more sources
Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys
Advanced Engineering Materials, EarlyView.This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa +9 more
wiley +1 more source
Measurement of frictional torque of a directacting valvetrain using a shaft-to-shaft torque transducer to study the effect of Laser Surface Texturing on friction reduction [PDF]
MATEC Web of ConferencesThe study of tribological applications requires measuring various parameters, including RPMs, friction, and wear. The useful information is sometimes not readily available in a measurement and requires further postprocessing to extract that information ...
Siddiqui Muhammad Rizwan +6 more
doaj +1 more source
Sensorless torque/force control [PDF]
, 2011 Motion control systems represent a main subsystem for majority of processing systems that can be found in the industrial sector. These systems are concerned with the actuation of all devices in the manufacturing process such as machines, robots, conveyor
Khalil, Islam Shoukry Mohammed +2 more
core +2 more sources