Results 41 to 50 of about 388,267 (293)

Torsions, low-frequency vibrations, and vibration–torsion (“vibtor”) levels in the m-chlorotoluene cation [PDF]

open access: yesThe Journal of Chemical Physics, 2020
Zero-electron-kinetic-energy (ZEKE) spectra are presented for m-chlorotoluene (mClT), employing different low-lying torsional and vibration–torsional (“vibtor”) levels of the S1 state as intermediates. The adiabatic ionization energy is determined to be 71 319 cm−1 ± 5 cm−1 (8.8424 ± 0.0006 eV).
David J. Kemp   +2 more
openaire   +2 more sources

New Damped-Jerk trajectory for vibration reduction [PDF]

open access: yes, 2014
This paper derives a jerk-shaped profile to address the vibration reduction of underdamped flexible dynamics of motion system. The jerk-limited profile is a widespread smooth command pattern used by modern motion systems.
BEAREE, Richard
core   +1 more source

Organic Materials of Tomorrow: Horizons of Artificial Intelligence

open access: yesAdvanced Materials, EarlyView.
This review examines machine learning techniques accelerating the discovery of organic semiconductors by linking molecular structure to properties. Key methods include graph neural networks, generative models, and active learning. Applications to organic photovoltaics demonstrate practical impact.
Harold Mena   +3 more
wiley   +1 more source

Torsional Vibration Test on the Shaft System of Reciprocating Compressor

open access: yesShiyou jixie, 2020
One certain type of compressor suffers excessive current fluctuation. In order to solve this problem, torsional vibration test was carried out on the compressor and the test results were analyzed by means of the analog multi-frequency sine sweep method ...
Wang Yibing   +3 more
doaj  

Improvement calculation accuracy of blade-shaft coupled torsional vibration by including axial shaft motion

open access: yesNihon Kikai Gakkai ronbunshu, 2019
Selected from various Eigen modes of blading, nodal diameter κ= 0 and κ= 1 are both related to shaft torsional and/or axial vibration and shaft bending vibrations respectively.
Hiroki NAKAMURA   +4 more
doaj   +1 more source

Soft Skins With Reversible Thickness Morphing: Materials, Mechanisms, and Applications

open access: yesAdvanced Materials, EarlyView.
Evolution of electronic skin (e‐skin) technologies toward adaptive, multifunctional soft skins. Phase I highlights early rigid and discrete sensory interfaces. Phase II shows the transition toward flexible, stretchable, and large‐area e‐skin. Phase III captures the emergence of computational e‐skin.
Oliver Ozioko   +2 more
wiley   +1 more source

Investigation of diesel generator shaft and bearing failures [PDF]

open access: yes, 2004
A shaft failure in a 634 kW diesel generator after 4000 hours of operation required investigation, especially when similar sets began to show signs of excessive bearing housing wear.
Craighead, I.A., Gray, T.G.F.
core   +4 more sources

Fast Hydrogel Micro‐Actuators Driven by Electric Fields

open access: yesAdvanced Materials, EarlyView.
We report the fabrication of chemically programmable electroactuating microstructures through the first integration of two‐photon polymerization with electrically actuated gelatin methacrylate‐based hydrogels. By tailoring the charge of the polymer network, we demonstrate programmable polarity‐dependent bending, enabling microstructures that ...
Annaël Sort‐Montenegro   +6 more
wiley   +1 more source

Investigation of gas circulator response to load transients in nuclear power plant operation [PDF]

open access: yes, 2012
Gas circulator units are a critical component of the Advanced Gas-cooled Reactor (AGR), one of the nuclear power plant (NPP) designs in current use within the UK.
Campbell, Graeme   +3 more
core   +3 more sources

Modeling and experimental analysis of cutting force in longitudinal–torsional ultrasonic-assisted milling of titanium

open access: yesAdvances in Mechanical Engineering, 2019
This study proposed a novel milling technology assisted by longitudinal–torsional compound ultrasonic vibration to overcome the difficulties in the processing of Ti-alloy heterogeneous surfaces or molding surfaces.
Xiaobo Wang   +3 more
doaj   +1 more source

Home - About - Disclaimer - Privacy