Results 91 to 100 of about 3,319,079 (328)

Passive compensation of nonlinear robot dynamics [PDF]

, 2004
In this paper, we derive a coordinate-free formulation of a passive controller that makes a mechanical system track reference curves in a potential field.
Duindam, Vincent, Scherpen, Jacquelien M.A., Stramigioli, Stefano   +2 more
core   +5 more sources

Investigation of the effect of the inspection intervals on the track geometry condition

, 2020
In order to evaluate the railway track geometry condition and plan maintenance activities, track inspection cars run over the track at specific times to monitor it and record geometry measurements.
I. Soleimanmeigouni, A. Ahmadi, Hamid Khajehei, A. Nissen   +3 more
semanticscholar   +1 more source

The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282

Advanced Engineering Materials, EarlyView.
The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh, Ahmed Fardan, Tatiana Mishurova, Eduard Hryha   +3 more
wiley   +1 more source

PBF‐LB/M of Ti‐6Al‐4V: High‐Pressure Solution Treatment and Aging for Applications in a Sustainable Aerospace

Advanced Engineering Materials, EarlyView.
Additive manufacturing (AM) allows great geometric freedom for lightweight components. As parts are progressively optimized exploiting potentials in AM leading in smaller material cross sections, high pressure solution treating and aging (STA) treatments show an enormous potential for strongly improving material properties.
Mika León Altmann, Andre Danzig, Freerk Syassen, Rainer Fechte‐Heinen, Anastasiya Toenjes   +4 more
wiley   +1 more source

Study on Key Factors on Ride Comfort of Low-floor Light Rail Transit [PDF]

E3S Web of Conferences
In order to meet the public’s demand for higher and higher comfort level of low-floor trams, this paper analyzes the influence on comfort level from four aspects: equivalent conicity, hinge arrangement position, suspension parameters and track geometry ...
Qiang Feng, Wu Na
doaj   +1 more source

A Thermodynamic 3D Model for the Simulation of Diffusion‐Controlled Alloying Processes in Heterogeneous Material Structures

Advanced Engineering Materials, EarlyView.
A numerical model resulting from irreversible thermodynamics for describing transport processes is introduced, focusing on thermodynamic activity gradients as the actual driving force for diffusion. Implemented in CUDA C++ and using CalPhaD methods for determining the necessary activity data, the model accurately simulates interdiffusion in aluminum ...
Ulrich Holländer, Leonhard Holländer, André Langohr, Hans Jürgen Maier   +3 more
wiley   +1 more source

Prediction of Rail Wear Under Different Railway Track Geometries Using Artificial Neural Networks

Infrastructures
The geometry of the railway track affects rail wear significantly. If the rail wear can be predicted and considered during the alignment design phase, the problems it causes can be mitigated at the source by optimizing the values and combinations of ...
Hong Zhang, Weichen Shuai, Linya Liu, Pengfei Zhang, Kejun Zhang, Hongsong Lin, Yuke Zhang, Wei Li   +7 more
doaj   +1 more source

Influences of Railway Track Geometry Parameters on Ground-Borne Vibration [PDF]

International Journal of Railway Research, 2014
One of the most important challenges in the development of urban railways network is the effects of railway vibrations on human and adjacent structures. Although various investigations into the sources of railway vibrations have been conducted, very few ...
Javad Sadeghi, M.H Esmaeili, M. Shadfar, A. Ashari Ghomi   +3 more
doaj  

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Laser Metal Powder Deposition of Titanium Microalloyed HSLA Steel FeC0.12Si0.25Mn1.3

Advanced Engineering Materials, EarlyView.
This study investigates the additive manufacturing of titanium‐doped high‐strength low‐alloy (HSLA) steel via laser metal deposition. It reveals distinct process‐structure relationships for elemental powder blends compared to prealloyed feedstocks.
Olaf Stelling, Matthias Steinbacher, Nils Ellendt   +2 more
wiley   +1 more source