Results 111 to 120 of about 229,475 (313)

The Central European buffer zone [PDF]

This paper considers the creation of a new region in Europe since the opening of the borders following the so-called "revolutions" in East-Central Europe.
Claire Wallace
core  

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Sensitivity and specificity of 24-hour-delayed radiographs in demonstrating the transition zone of Hirschsprung disease

Journal of Health Science and Medical Research (JHSMR), 2010
Objective: Our aims were to determine the sensitivity and specificity of the practice of 24-hour-delayed radiographs used to demonstrate the transition zone of Hirschsprung disease.
Teeranan Laohawiriyakamol, Pramot Tanutit   +1 more
doaj  

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

(Table 1) Grain size composition of tuff (tuff breccia) with subsilicic-ultrabasite inclusions from the transition zone of the Reykjanes Ridge

, 1997
(Table 1) Grain size composition of tuff (tuff breccia) with subsilicic-ultrabasite inclusions from the transition zone of the Reykjanes ...
Gennady S Kharin (6959660), Kharin, Gennady S   +1 more
core   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

A soft edge target zone model: Theory and application to Hong Kong [PDF]

Hong Kong’s currency is pegged to the US dollar in a currency board arrangement. In autumn 2003, the Hong Kong dollar appreciated from close to 7.80 per US dollar to 7.70, as investors feared that the currency board would be abandoned.
Chen, Yu-Fu, Funke, Michael, Glanemann, Nicole   +2 more
core  

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Taxa‐dependent temporal trends in the abundance and size of sea urchins in subtropical eastern Australia

Ecology and Evolution
Subtropical reefs host a dynamic mix of tropical, subtropical, and temperate species that is changing due to shifts in the abundance and distribution of species in response to ocean warming.
Emily McLaren, Brigitte Sommer, John M. Pandolfi, Maria Beger, Maria Byrne   +4 more
doaj   +1 more source