Results 81 to 90 of about 1,396,285 (293)

Research on the seedling picking trajectory error of the gear train seedling picking mechanism considering tooth backlash

Engineering Reports
The research investigated the tooth backlash influences the error in seedling picking trajectories of the gear train SPM. First, a sine function and the sum of random errors are taken into account is utilized to fit the tooth backlash of the firstly and ...
Fengjiao Du, Jiangang Liu, Peng Qi
doaj   +1 more source

Towards Defect Phase Diagrams: From Research Data Management to Automated Workflows

Advanced Engineering Materials, EarlyView.
A research data management infrastructure is presented for the systematic integration of heterogeneous experimental and simulation data required for defect phase diagrams. The approach combines openBIS with a companion application for large‐object storage, automated metadata extraction, provenance tracking and federated data access, thereby supporting ...
Khalil Rejiba, Sang‐Hyeok Lee, Christina Gasper, Martina Freund, Sandra Korte‐Kerzel, Ulrich Kerzel   +5 more
wiley   +1 more source

Multi-Objective Optimization Design of Cycloid-Pin Gears Based on RV Reducer Precision Transmission Performance

Energies
This paper aims to realize multi-objective optimization of cycloid-pin gears to improve the positioning accuracy and load-carrying capacity of the rotary vector (RV) reducer, via the consideration of backlash, transmission error, and torsional stiffness.
Yunda Zhao, Zhenhua Han, Qifeng Tan, Wentao Shan, Rirong Li, Hao Wang, Youwu Du   +6 more
doaj   +1 more source

Dynamic simulation of a motor longitudinally mounted on a centralized electric drive systems for pure electric vehicles under torque ripple and transmission error excitations. [PDF]

Sci Prog, 2023
Liao Z, Hua X, Cheng X, Ning X, Liu Z, Chen G.   +5 more
europepmc   +1 more source

An error floor in tone calibrated transmission [PDF]

Use of a low level pilot tone has been shown to eliminate the error floor in fading channels. This paper demonstrates that non-idealities in the receiver's pilot tone filter cause reappearance of the error floor. It also presents the bit error rate (BER)
Cavers, James K.
core   +1 more source

Deterministic Detection of Single Ion Implantation

Advanced Engineering Materials, EarlyView.
Focused ion beam implantation with high detection efficiencies will enable the rapid and scalable fabrication of advanced spin‐based technologies such as qubits. This work presents the detection efficiencies of a wide range of ions implanted into solid‐state hosts, with efficiencies of >90% recorded for ion species and substrate combinations of ...
Mason Adshead, Lok Kan Wan, Maddison Coke, Janet Jacobs, Nicholas F. L. Collins, Mark C. Rosamond, Richard J. Curry   +6 more
wiley   +1 more source

An Ease-Off Based Tooth Contact Analysis Method for Measured Face Gear Flanks

Applied Sciences
To rapidly evaluate the meshing performance of manufactured face-gear drives, this study proposes an efficiency-optimized tooth contact analysis (TCA) method for measured gear flanks based on Ease-off surface. Initially, mathematical models of the pinion
Zhongwei Tang, Yuansheng Zhou, Jinyuan Tang   +2 more
doaj   +1 more source

The effect of errors in the assignment of the transmission functions on the accuracy of the thermal sounding of the atmosphere [PDF]

In order to test the error of calculation in assumed values of the transmission function for Soviet and American radiometers sounding the atmosphere thermally from orbiting satellites, the assumptions of the transmission calculation is varied with ...
Timofeyev, Y. M.
core   +1 more source

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source

Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing

Advanced Engineering Materials, EarlyView.
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai, Zeki Ayrildi, Buse Şen, Maik Rajkowski, Mathias Redondo Garcia, Markus Stricker, Guillaume Laplanche   +6 more
wiley   +1 more source