Results 281 to 290 of about 1,515,846 (349)

Scarce evidence of ozone effects on tree defoliation and growth in Trentino

, 2013
M. Ferretti, Giovanni Bacaro, Giorgio Brunialti, Massimo Confalonieri, Luisa Frati, Simona Maccherini, Cristofolini, Fabiana, Cristofori, Antonella, Elena Gottardini   +8 more
openalex   +1 more source

Viscum album in French forests: Distribution, environmental drivers and impacts on tree health and growth

William Marchand, Jean-Baptiste Daubrée, Claire Depardieu   +2 more
openalex   +1 more source

Flexible 3D Multi‐Material Printing beyond Layer‐by‐Layer Constraints via Sequential Multi‐Printer Fabrication

Advanced Materials Technologies, EarlyView.
We developed a flexible multi‐material printing strategy that employs sequential printing with different printers. This combined use of printers expands the accessible material scope. Moreover, incorporating Xolography as a sequential step enables support‐free, contactless printing, thereby enhancing structural design flexibility beyond conventional ...
Kun Zhou, Cyrille Boyer
wiley   +1 more source

Monitoring canopy SPAD based on UAV and multispectral imaging over fruit tree growth stages and species. [PDF]

Front Plant Sci
Huang Y, Li D, Liu X, Ren Z.
europepmc   +1 more source

Additive Manufacturing of Patient‐Specific Intracranial Aneurysm Cell Culture Models

Advanced Materials Technologies, EarlyView.
Patient‐specific intracranial aneurysm models were fabricated using chocolate moulding, 3D printed water‐soluble cores, and direct resin 3D printing. Moulding PDMS around sacrificial cores made of chocolate or 3D printed water‐soluble resin yielded accurate, expandable, and endothelializable models that outperformed resin‐based approaches.
Chloe M. de Nys, Jaimee‐Lee Wood, James I. Novak, Danilo Carluccio, Craig D. Winter, Ashley R. Murphy, Mark C. Allenby   +6 more
wiley   +1 more source

Additive Manufacturing of Ni‐Based Thermoelectric Materials for Waste Heat Recovery

Advanced Materials Technologies, EarlyView.
Thermoelectric generators convert waste heat into electricity but are constrained by conventional fabrication. Here, laser powder bed fusion enables direct printing of customised n‐type Cu60Ni40 and p‐type Ni90Cr10 legs. The assembled module achieves 0.8% efficiency at ΔT = 419 K, demonstrating scalable additive manufacturing of eco‐friendly, design ...
Karolin Amstein, Aayush Dobhal, Heiko Reith, Ran He, Julia Kristin Hufenbach, Kornelius Nielsch, Pingjun Ying   +6 more
wiley   +1 more source

A Handheld Laser-Scanning-Based Methodology for Monitoring Tree Growth in Chestnut Orchards. [PDF]

Sensors (Basel)
Pereira-Obaya D, Cabo C, Ordóñez C, Rodríguez-Pérez JR.   +3 more
europepmc   +1 more source

Improving growth of shea butter tree (Vitellaria paradoxa C.F. Gaertn.) seedlings using mineral N, P and arbuscular mycorrhizal (AM) fungi

, 2009
Mahamadi Dianda, Jules Bayala, Tahir Abdoulaye Diop, Ouédraogo SJ.   +3 more
openalex   +1 more source

Hierarchical Multi‐Material Architectures With Gradient Design for Dynamic‐Range Flexible Tactile Sensing

Advanced Materials Technologies, EarlyView.
Hierarchical multi‐material TPMS lattices are engineered as flexible tactile sensors by combining soft and stiff elastomeric layers with a conformal conductive coating. The bilayer architecture delivers sensitivity at low pressures while maintaining a broad detectable range under large loads, enabling reliable pressure and vibration monitoring for ...
Reza Noroozi, Domenic Quiquero, Yan Yan Shery Huang, HaoTian Harvey Shi   +3 more
wiley   +1 more source

pACP-HybDeep: predicting anticancer peptides using binary tree growth based transformer and structural feature encoding with deep-hybrid learning. [PDF]

Sci Rep
Shahid, Hayat M, Alghamdi W, Akbar S, Raza A, Kadir RA, Sarker MR.   +6 more
europepmc   +1 more source