Results 101 to 110 of about 6,058 (212)

Multi-Objective Optimization of Tribological Characteristics for Aluminum Composite Using Taguchi Grey and TOPSIS Approaches

Lubricants
In this study, a multi-objective optimization regarding the tribological characteristics of the hybrid composite with a base material of aluminum alloy A356 as a constituent, reinforced with a 10 wt.% of silicon carbide (SiC), size 39 µm, and 1, 3, and 5
Sandra Gajević, Ana Marković, Saša Milojević, Aleksandar Ašonja, Lozica Ivanović, Blaža Stojanović   +5 more
doaj   +1 more source

Influence of Some Microchanges Generated by Different Processing Methods on Selected Tribological Characteristics. [PDF]

Micromachines (Basel), 2021
Nagîț G, Slătineanu L, Dodun O, Mihalache AM, Rîpanu MI, Hriţuc A.   +5 more
europepmc   +1 more source

Auger Parameter Analysis for TiN and AlN Thin Films via Combined In Situ XPS and HAXPES

Surface and Interface Analysis, Volume 58, Issue 6, Page 387-399, June 2026.
ABSTRACT Auger parameter analysis provides in‐depth information about electronic and chemical bonding properties of TiN and AlN thin films, which are relevant across a wide range of technologies. Meaningful interpretation and analysis of Auger parameter of these materials have been hindered due to, among other reasons, the absence of reliable ...
O. V. Pshyk, J. Patidar, C. Cancellieri, S. Siol   +3 more
wiley   +1 more source

Effect of Functional Fillers on Tribological Characteristics of Acrylonitrile Butadiene Rubber after High-Pressure Hydrogen Exposures. [PDF]

Polymers (Basel), 2022
Choi BL, Jung JK, Baek UB, Choi BH.
europepmc   +1 more source

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, Volume 28, Issue 9, 6 May 2026.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Investigation of the Tribological Characteristics of Aluminum 6061-Reinforced Titanium Carbide Metal Matrix Composites. [PDF]

Nanomaterials (Basel), 2021
Veeresh Kumar GB, Pramod R, Hari Kiran Reddy R, Ramu P, Kunaal Kumar B, Madhukar P, Chavali M, Mohammad F, Khiste SK.   +8 more
europepmc   +1 more source

Investigation of Structural, Mechanical and Electrochemical Properties of Temperature‐Dependent Dual AlN/TiAlN Coating Synthesized by CVD Process

Advanced Materials Interfaces, Volume 13, Issue 9, 5 May 2026.
This study investigates thermally CVD‐deposited AlN/TiAlN dual‐layer coatings over a Si substrate, focusing on the temperature‐dependent process‐structure relationship. Systematic characterization reveals that a dense AlN interlayer combined with an optimally deposited TiAlN top layer provides enhancement in mechanical strength, tribological stability,
Soham Das, Abhishek Kundu, Debjyoti Sahu, Nikhil Kumar, Spandan Guha   +4 more
wiley   +1 more source

The Correlation Analysis of Microstructure and Tribological Characteristics of In Situ VCp Reinforced Iron-Based Composite. [PDF]

Materials (Basel), 2021
Zhang Y, Lai R, Chen Q, Liu Z, Li R, Chen J, Chen P.   +6 more
europepmc   +1 more source

Multiresponse Tribological Ranking Alternatives of Al–Cu Alloys via an Integrated Taguchi Experimental Design, AHP Weighting, and WASPAS Decision Framework

Engineering Reports, Volume 8, Issue 5, May 2026.
To optimize aluminium–copper alloy compositions and tribological parameters for improved wear performance using an integrated hybrid MCDM approach. The Al–Cu alloy compositions were fabricated through die casting. Their tribological performance was evaluated and optimized using a hybrid Taguchi–AHP–WASPAS methodology under varying loads, sliding speeds,
S. P. Sundar Singh Sivam, Venugopal Gurusamy Umasekar, Stalin Kesavan, A. Johnson Santhosh   +3 more
wiley   +1 more source

Low‐Cost Friction‐Based Force‐Limiting Connection With Reduced Sensitivity to Machining Tolerances and Accelerated Repairability

Earthquake Engineering &Structural Dynamics, Volume 55, Issue 6, Page 1270-1291, May 2026.
ABSTRACT This paper presents a novel yet practical friction‐based structural component design for low‐damage earthquake‐resistant structures. The proposed connection design is based on a conventional slotted‐bolted configuration with the novelty being the use of loose steel washer plates to establish the friction‐sliding interface.
Kaixin Chen, Georgios Tsampras, Chung‐Che Chou, Huang‐Zuo Lin, Chi‐Jeng Wu, Alvaro Córdova, Chia‐Ming Uang, Shih‐Ho Chao   +7 more
wiley   +1 more source