Results 11 to 20 of about 651 (172)
Synchrotron X-ray tomography and spectroscopy in numismatics: disclosing counterfeit practices in medieval silver coins. [PDF]
J Synchrotron RadiatAdvanced synchrotron‐radiation‐based imaging and spectroscopic techniques were used to investigate the distribution and nature of mercury in numismatic artifacts, with a particular focus on its role in historical counterfeiting practices.This study explores the use of advanced synchrotron radiation (SR)‐based imaging and spectroscopic techniques to ...
Raneri S +4 more
europepmc +2 more sources
Fe-Based Nanocrystalline Magnetic Shielding Cylinder with Subfemtotesla-Level Magnetic Noise. [PDF]
Adv Sci (Weinh)Shields with low magnetic noise are achieved by integrating Fe‐based nanocrystalline magnetic shielding cylinders into shielding systems based on μ‐metal. Benefiting from high permeability and low loss factor, Fe‐based nanocrystalline magnetic shielding cylinders effectively suppress magnetic noise. Notably, the magnetic shielding cylinder with the ten‐
Shen P +13 more
europepmc +2 more sources
Optimization of flow control devices in a 40-t single strand tundish
工程科学学报, 2015 An optimization of flow control "devices in a 40-t single strand continuous casting tundish was carried out by water modeling experiments and industrial experiments. Three cases were considered during the experiments, i.
ZHAO Li-hua, WANG Min, LI Ning
doaj +1 more source
Metals, 2022 Reducing the volume of distributing chamber by shortening its width is one of the ways to obtain good metallurgical effects for a large two-strand induction heating tundish.
Bin Yang +4 more
doaj +1 more source
Process design and life anylysis of tundish lining
Metalurgija, 2021 The working lining of continuous casting tundish is made of magnesia dry material with short service life. It is found that the refractory lining cast steel zone is the key to influence the service life of tundish.
J. H. Zhang, Y. X. Chen, D. Z. Yang
doaj
Physical simulation of tundish heated by plasma
工程科学学报, 2020 This study proposes a model to increase the heating efficiency of tundish plasma heating and improve the flow of molten steel in a tundish during production.
Yong WANG +5 more
doaj +1 more source
Numerical Modeling of the Fluid Flow in Continuous Casting Tundish with Different Control Devices
Abstract and Applied Analysis, 2013 Numerical simulations were conducted to study the melt flow under the influence of control devices in a T-type two-strand bloom caster tundish via the open source Computational Fluid Dynamics software OpenFOAM.
Zhu He +4 more
doaj +1 more source
Fluid Flow and Heat Transfer Behaviors under Non-Isothermal Conditions in a Four-Strand Tundish
Metals, 2022 In the continuous casting process, the fluid flow of molten steel in the tundish is in a non-isothermal state. Because of the geometric shape and process parameters of a multi-strand tundish, the fluid flow behavior of each strand is quite inhomogeneous,
Mingmei Zhu +5 more
doaj +1 more source
Study and Application on Physical Simulation of Single Thick Slab Flow Tundish
Teshugang, 2022 In order to obtain a more reasonable 50 t tundish flow control device, a single flow tundish water model with a geometrical similarity ratio of 1:4 is established, and physical simulation tests are carried out to study the effects of different flow rates
Jiang Xuefeng +3 more
doaj
steel research international, EarlyView.In primary electric arc furnace (EAF) steelmaking, carbon boiling removes nitrogen from liquid steel and sustains slag foaming. In 100% scrap‐ or hydrogen direct reduced iron (HDRI)‐based EAF steelmaking, carbon boiling is absent; therefore, carbonaceous material and oxygen injection into the slag is needed to maintain foaming and avoid nitrogen ...
Zushu Li +3 more
wiley +1 more source