Results 121 to 130 of about 656,186 (313)

Evaluation of Creatinine-Based Methods for Estimating the Urine Volume of Lactating and Dry Dairy Cows with Special Consideration of Using Spot Urine Samples

open access: yesRuminants
A key factor in calculating dairy cows’ nitrogen (N) excretion is knowing the amount of daily excreted urine. The present study aimed to investigate two methods to calculate the daily urine volume (UV) excreted using spot urine samples.
Katharina Padberg   +7 more
doaj   +1 more source

Gemifloxacin mesylate: UV spectrophotometric method for quantitative determination using experimental design for robustness

open access: yesQuímica Nova, 2012
This study describes the validation of UV spectrophotometric method for quantitative determination of gemifloxacin mesylate (GFM) in tablets using methanol as solvent. The method was specific, linear, precise, exact and robust at 272 and 343 nm.
Clésio Soldateli Paim   +3 more
doaj   +1 more source

Designing Polymer Nanocomposites for X‐Ray Shielding: Mechanisms, Architectures, and Scalable Processing

open access: yesAdvanced Engineering Materials, EarlyView.
This review highlights advances in lightweight, lead‐free polymer nanocomposites for diagnostic X‐ray shielding. By linking filler chemistry, dispersion, architecture, and photon interaction mechanisms, it establishes structure–performance relationships guiding material design.
Aklilu G. Messele   +2 more
wiley   +1 more source

A Dislocation Perspective on Strength and Toughness in Ceramics

open access: yesAdvanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

open access: yesAdvanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim   +3 more
wiley   +1 more source

Determination of EDTA in dairy wastewater and adjacent surface water

open access: yes, 2010
An HPLC-UV analytical method was developed to determine ethylenediaminetetraacetic acid (EDTA) in dairy wastewater and surface water. The optimizing separation was achieved by reversed–phase ion-pair liquid chromatography on a C18 column using methanol ...
Xie, Congmin Zoe   +3 more
core  

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

open access: yesAdvanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev   +2 more
wiley   +1 more source

UV-induced DNA damage in humans

open access: yes, 1998
Ultraviolet radiation is considered to be the most harmful part of solar energy affecting man. The depletion of the ozone layer around the Earth increases the total exposure to UV-light. The incidence of skin cancer in man has been shown to be associated
Vladimir J Bykov (19525825)
core  

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

open access: yesAdvanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

Laser‐Induced Graphene from Waste Almond Shells

open access: yesAdvanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova   +9 more
wiley   +1 more source

Home - About - Disclaimer - Privacy