Results 21 to 30 of about 19,778 (262)
Diagnosis of the power frequency vacuum arc shape based on 2D-PIV
Open Physics, 2018 Vacuumcircuit breaker (VCB) is one of the important elements in the power grid that can control and protect the system. The diagnosis of the vacuum arc images in VCBs is helpful to the study on their breaking performance.
Dong Wenliang +2 more
doaj +1 more source
Protective Woodcutting Tool Coatings
Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 2016 The modern woodworking industry applies resource-saving, environmentally appropriate technologies, providing both the metal removal performance enhancement and functioning with the optimal economic factors.
Svetlana D. Latushkina +8 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
On the Prediction of Macrosegregation in Vacuum Arc Remelted Ingots
Metallurgical and Materials Transactions B, 2022 The chemical homogeneity and metallurgical structure of vacuum arc remelted (VAR) zirconium ingots are directly responsible for product quality. It is therefore important to understand the relationship between these properties and the operating conditions. An in-depth analysis of the modelling of solidification phenomena during the VAR was carried out.
Mramor, K. +6 more
openaire +4 more sources
Advanced Engineering Materials, EarlyView.A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Simulation study on modeling of vacuum arc characteristics and anode temperature rise in low-frequency vacuum interruption [PDF]
AIP AdvancesLow-frequency transmission technology has been widely used in medium- and long-distance electricity transmission scenarios such as offshore wind power transmission due to its advantages of low cost and strong ability to pool renewable energy.
Yanting Li +6 more
doaj +1 more source
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee +7 more
wiley +1 more source