Results 51 to 60 of about 3,631,519 (286)
Advanced Engineering Materials, EarlyView.Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver +9 more
wiley +1 more source
Experimental Study on the Dynamic Performance of Water-Lubricated Rubber Bearings with Local Contact
Shock and Vibration, 2018 Accurate dynamic characteristic coefficients of water-lubricated rubber bearings are necessary to research vibration of ship propulsion system. Due to mixed lubrication state of water-lubricated rubber bearings, normal test rig and identification method ...
Wu Ouyang +3 more
doaj +1 more source
Friction and Wear Properties of Rice Husk Ceramics under Dry and Water Lubricated Conditions
Tribology Online, 2009 The authors have developed the new hard porous carbon material “Rice Husk ceramics” (RH ceramics) by carbonizing the mixture of rice husk and phenol resin at 900 °C in inert gas environment.
Tuvshin Dugarjav +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Influence of undissolved gas on the characteristics of high-speed water-lubricated bearings
工程科学学报, 2017 Unlike the traditional oil-lubricated bearing, the water-lubricated bearing has unique advantages because of which lead it has important applications in all types of high-speed rotating machinery.
YANG Yu-mou, FENG Ming
doaj +1 more source
Electrified Damage in Motion Systems
Advanced Engineering Materials, EarlyView.The electrified damage in motion systems is a fundamental framework presenting the degradation pathway arising from the coupling of electrical energy transport with mechanical contact and interfacial chemistry. The framework positions electrified damage as a distinct degradation regime with unique characteristic surface morphologies and failures of ...
M. Humaun Kabir +2 more
wiley +1 more source
Research on the Structure Design of Composite Water-lubricated Stern Bearing
Jixie chuandong, 2021 Based on the ANSYS CFX fluid-structure interaction numerical calculation method， the lubrication performance and structure design of water-lubricated composite stern bearing are studied， the effects laws of different grooves， clearance ratios， length ...
Yanzhen Wang +3 more
doaj
Friction and wear behavior of different seal materials under water-lubricated conditions
Friction, 2020 The shaft mechanical face seal in a high-speed turbopump of a liquid rocket engine often operates under extremely harsh conditions. For example, a low-temperature and low-viscosity fluid (such as liquid oxygen or liquid hydrogen) is used as a lubricant ...
Weigang Zhao +2 more
doaj +1 more source
Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition
Advanced Engineering Materials, EarlyView.AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley +1 more source
EFFECT OF SURFACE ROUGHNESS ON FRICTION COEFFICIENT OF RECYCLED RUBBER FLOORINGS [PDF]
Journal of the Egyptian Society of Tribology, 2013 The effect of surface roughness on the frictional behaviour of recycled rubber tiles is discussed. Experiments were carried out by the sliding of the bare foot against the tested rubber tiles of different thickness.
B. R. Elham, W. Y. Ali, M. I. Khashaba
doaj +1 more source