Results 131 to 140 of about 4,534 (259)

Effect of Polyether Ether Ketone Melt Fluidity on Crystallization Behavior of Carbon Fiber Reinforced Polyether Ether Ketone Composites. [PDF]

Molecules
Liu W, Miao X, Tao S, Li J, Ma J, Yang J, Li H.   +6 more
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Resonant X-Ray Diffraction of Conjugated Polymers at the Selenium K-Edge. [PDF]

Macromol Rapid Commun
Freychet G, Kirby N, Gebert M, Kim YH, He Q, Heeney M, McNeill CR.   +6 more
europepmc   +1 more source

Variable Stiffness Flexure Structures Enabled by Phase‐Change Gallium and Adhesive Interfacial Locking for Soft Robotic Applications

Advanced Engineering Materials, EarlyView.
A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim, Sohee John Yoon, Yong‐Lae Park   +2 more
wiley   +1 more source

In situ synchrotron X-ray scattering reveals organic-mediated scaling mechanisms on desalination membranes. [PDF]

Nat Commun
Feng Z, Xu S, Cao J, Ren Z, Yang Y, Jiang J, Feng X, Lu X.   +7 more
europepmc   +1 more source

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source

Fluorescent Poly(vinyl alcohol) Composite Films Incorporating Doped Carbon Dots for Heavy Metal Detection in Smart Packaging Applications. [PDF]

ACS Omega
Mitcharean C, Kedsakon K, Hasdin O, Busayaporn W, Chunhakowit P, Songsrirote K, Prayongpan P.   +6 more
europepmc   +1 more source

Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition

Advanced Engineering Materials, EarlyView.
A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley   +1 more source

Investigating the Durability of PHA-Coated Burlap for Coastal Restoration. [PDF]

ACS Appl Eng Mater
Gadimli R, Thomas C, Omand MM, Albert JNL.   +3 more
europepmc   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source