Results 91 to 100 of about 9,664,256 (306)
Wear mechanisms and microstructure of pulsed plasma nitrided AISI H13 tool steel
, 2010 AISI H13 tool steel discs were pulsed plasma minded during different times at a constant temperature of 400 degrees C Wear tests were performed in order to study the acting wear mechanisms The samples were characterized by X-ray diffraction, scanning ...
MEI, P. R. +7 more
core +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
, 2018 The objective of this study is to identify and explain tool wear mechanisms that dominate during machining of titanium alloy Ti-6Al-4V in dry, flood coolant, and minimum quantity lubrication (MQL) conditions.
Ashutosh Khatri, M. P. Jahan
semanticscholar +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Journal of Manufacturing and Materials ProcessingHigh-strength quenched and tempered steels such as EN 42CrMo4, widely used for marine shaft applications due to their high strength, toughness, and fatigue resistance, are nevertheless susceptible to surface degradation under severe dry sliding ...
Stavros K. Chionopoulos +1 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat +7 more
wiley +1 more source
A multiscale tribological study of nacre : Evidence of wear nanomechanisms controlled by the frictional dissipated power [PDF]
, 2012 Sheet nacre is a hybrid biocomposite with a multiscale structure, including nanograins of CaCO3 (97% wt.% – 40 nm in size) and two organic matrices: (i) the “interlamellar” mainly composed of β-chitin and proteins, and (ii) the “intracrystalline” mainly ...
Stempflé, Philippe +5 more
core
Micro-abrasion resistance of thermochemically treated steels in aqueous solutions: Mechanisms, maps, materials selection [PDF]
, 2008 The area of micro-abrasion is an interesting and relatively recent area in tribo-testing methodologies, where small particles of less than 10 μm are employed between interacting surfaces.
Rocha, L.A. +7 more
core +1 more source
Performance Analysis of Abradable Coating Systems for Aircraft Gas Turbines
Advanced Engineering Materials, EarlyView.Three CoNiCrAlY/YSZ/MgAl2O4 abradable liner configurations on a nickel‐superalloy are evaluated by thermal‐gradient cycling and incursion tests. Laser ablation of the bondcoat and/or Y2O3‐stabilized ZrO2 (YSZ) intermediate layer increases mechanical interlocking and bonding for thick topcoats.
Hanna Heyl +4 more
wiley +1 more source
Sliding wear of nitrided steels
, 1993 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.The unlubricated sliding wear behaviour of gas nitrided, plasma nitrided, and ferritic nitrocarburized BS970,905M39 (EN41B) steels was investigated ...
Kato, Hirotaka, Kato, H
core