Results 101 to 110 of about 5,559,545 (283)

Tribological Investigation of Plasma-Based Coatings for Use in Quasi-Monolithic Engine Cylinder Bores

Metals
This study evaluates the tribological characteristics of quasi-monolithic engine cylinder coatings and piston rings using a custom-built linear reciprocating tribometer.
Siddharth Banerjee, Joshua Stroh, Dimitry Sediako, Jimi Tjong   +3 more
doaj   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Method for real-time prediction of cutter wear during shield tunnelling: A new wear rate index and MCNN-GRU. [PDF]

MethodsX, 2023
Zhang N, Zhao LS.
europepmc   +1 more source

Rotary 3D Printing With Integrated Electroplating

Advanced Engineering Materials, EarlyView.
A rotary material extrusion platform integrates localized copper electroplating with printing and encapsulation to fabricate cylindrical polymer–metal structures containing fully embedded, low‐resistance conductive pathways that enable internal Joule heating and thermally activated shape‐memory responses.
Antonio Zagaria, Nicola Larovere, Moslem Mohammadi, Gianluca Percoco, Ali Zolfagharian, Gianni Stano   +5 more
wiley   +1 more source

Alumina-Toughened-Zirconia with Low Wear Rate in Ball-on-Flat Tribological Tests at Temperatures to 500 °C. [PDF]

Materials (Basel), 2021
Grabowy M, Wojteczko K, Wojteczko A, Wiązania G, Łuszcz M, Ziąbka M, Pędzich Z.   +6 more
europepmc   +1 more source

Composites of Shellac and Silver Nanowires as Flexible, Biobased, and Corrosion‐Resistant Transparent Conductive Electrodes

Advanced Functional Materials, EarlyView.
Shellac, a centuries‐old natural resin, is reimagined as a green material for flexible electronics. When combined with silver nanowires, shellac films deliver transparency, conductivity, and stability against humidity. These results position shellac as a sustainable alternative to synthetic polymers for transparent conductors in next‐generation ...
Rahaf Nafez Hussein, Tiago Carneiro Gomes, Eliza Ng, Simon Rondeau‐Gagné, Tricia Breen Carmichael   +4 more
wiley   +1 more source

A Comparative Analysis of Machine Learning Techniques for Predicting the Wear Rate of Ceramic Coated Steel

IEEE Access
Ceramic coatings are necessary for steel as they offer resistance to corrosion, high-temperature degradation, and abrasion, thereby enhancing the wear characteristics of steel structures.
N. Radhika, M. Sabarinathan, S. Sivaraman   +2 more
doaj   +1 more source

The Wear Rate Forecast of MgO-C Materials Type MC95/10 in the Slag Spout Zone of an Oxygen Converter in Terms of the Bayesian Estimation. [PDF]

Materials (Basel), 2022
Zelik W, Sado S, Lech R.
europepmc   +1 more source

Counterion Dependent Side‐Chain Relaxation Stiffens a Chemically Doped Thienothiophene Copolymer

Advanced Functional Materials, EarlyView.
Oxidation of a thienothiophene copolymer, p(g3TT‐T2), via different doping strategies and dopant molecules resulted in materials with similar oxidation levels and a high electrical conductivity of ≈100 S cm−1. However, mechanical properties varied significantly, with sub‐glass transition temperatures and elastic moduli spanning from –44°C to –3°C and ...
Mariavittoria Craighero, Meghna Jha, Elsa Veronica Flores‐Vela, Joost Kimpel, Andreas Schaefer, Jiali Guo, Jesika Asatryan, Alberto Peinador Veiga, Shuichi Haraguchi, Per‐Anders Carlsson, Jaime Martín, Mariano Campoy‐Quiles, Christian Müller   +12 more
wiley   +1 more source

Analysis of Microstructural and Wear Mechanisms for 3D-Printed PET CF15 Using Box–Behnken Design

Lubricants
We examined the impact of 3D-printing parameters, such as the deposition pattern, deposition speed, and layer height, on the tribological performance measured through the coefficient of friction and cumulative linear wear.
Alexandra Ileana Portoaca, Alin Dinita, Razvan George Ripeanu, Maria Tănase   +3 more
doaj   +1 more source