Results 1 to 10 of about 73,500 (284)
Wear and Friction Behavior of Plasma Sprayed NiCrMo-NiCrBSi Alloy Anti-Friction Coatings [PDF]
Cailiao Baohu, 2023 When the internal combustion engine is working， the friction between the piston ring and the cylinder liner will cause energy loss and wear damage to the cylinder block.Aiming at the problem of friction and wear of cylinder liner and piston ring， a ...
DONG Xinyuan, DENG Jianji, LUO Xiaotao, LI Changjiu
doaj +1 more source
Tribological properties of the SLM-316L filament under the grease lubrication condition
工程科学学报, 2021 To study the friction and wear properties of 316L stainless steel filaments prepared by selective laser melting (SLM) for metal rubber under the condition of grease lubrication, the friction coefficient and wear rate of SLM-316L filaments under different
Ming-ji HUANG +2 more
doaj +1 more source
Study on friction and wear properties of TC4 titanium alloy wire
Fenmo yejin jishu, 2023 The friction and wear properties of the TC4 titanium alloy wire under the dry friction conditions were studied. The influence of load (F) and friction speed (V) on the friction coefficient and wear rate of the TC4 wire was investigated.
ZHANG Zhiwen +3 more
doaj +1 more source
Advances in Materials Science and Engineering, 2021 The surface texture, a major way to decrease friction and wear of the cylinder-piston ring friction pair, was conducted on cylinder-piston ring friction pair specimen using the orthogonal experimental design method to investigate the effect of different ...
Wen’an Wang +4 more
doaj +1 more source
Friction and wear behavior of commercially pure titanium TA1 at high temperature
Cailiao gongcheng, 2021 The plastic shear resistance of commercially pure titanium (TA1) surface is low and the protective effect of oxide film is limited. Serious wear behavior will occur during sliding friction.
ZHANG Jia-ming, YU Wei, ZHANG Ze-yu
doaj +1 more source
EFFECT OF TALC AS SOLID LUBRICANT DISPERSING LITHIUM GREASE IN REDUCING FRICTION COEFFICIENT AND WEAR IN DUSTY ENVIRONMENT [PDF]
Journal of the Egyptian Society of Tribology, 2012 In cement factories abrasive contaminants cause severe wear of moving surfaces leading to rapid failure of the machine elements. In the present study, talc used as solid lubricants dispersed in lithium grease.
A. M. Samy
doaj +1 more source
Cailiao gongcheng, 2022 In order to solve the overheating failure problem of mechanical brakes of special tracked vehicles, SiC/Cu and SiC/Fe bi-continuous composites were prepared by squeeze casting method.
HUI Yang +3 more
doaj +1 more source
Adhesion, Friction, and Wear [PDF]
MRS Bulletin, 1991 In the context of this article, adhesion, friction, and wear are defined as follows: Adhesion is the resistance against separation of two bodies in a direction normal to the common interface. Friction is the resistance against motion of the contacting bodies in the direction of the common interface.
Landheer, D., Gee, de, A.W.J.
openaire +2 more sources
Wear Characteristics of Different Groove-Shaped Friction Pairs of a Friction Clutch
Applied Sciences, 2020 To investigate the influence of the groove shape of friction disks on the wear of a friction clutch friction pair, a wear calculation model that considers the actual sliding distance between the friction clutch friction pair is presented based on the ...
Heyun Bao +3 more
doaj +1 more source
Applied Sciences, 2023 Instantaneous friction and wear energy density are important indicators of the friction and wear state of the tooth flank of the milling cutter. Existing methods for identifying the friction and wear on the tooth flank of milling cutters mainly focus on ...
Bin Jiang +4 more
doaj +1 more source