Wear resistant multilayer nanocomposite WC1−x/C coating on Ti–6Al–4V titanium alloy [PDF]
, 2015 A significant improvement of tribological properties on Ti–6Al–4V has been achieved by developed in this study multilayer treatment method for the titanium alloys.
Mathia, T.G. +7 more
core +1 more source
The effect of retained austenite on the wear mechanism of bainitic ductile iron under impact load
Journal of Materials Research and Technology, 2021 The effect of retained austenite on the impact wear resistance of bainitic ductile iron is studied. Two kinds of bainitic ductile iron with different morphologies of retained austenite were fabricated via continuous cooling process.
Yongjin Wang, Renbo Song, Liang Huang
doaj +1 more source
Running-in wear modeling of honed surface for combustion engine cylinder liners [PDF]
, 2013 The texture change during running-in alters the performance and efficiency of a tribo-mechanical system. During mass production of cylinder liners, a final finishing stage known as ‘‘plateau honing’’ is commonly added to reduce the running-in wear ...
EL MANSORI, Mohamed +3 more
core +1 more source
Sliding wear of a-C:H coatings against alumina in corrosive media [PDF]
, 2013 This paper reports the results obtained from the study of friction and sliding wear in two corrosive solutions of an a-C:H coating deposited on 316L stainless against an alumina ball, employed as static counter part. Calculations of the values of the von
La Barbera Sosa, J.G. +16 more
core +1 more source
Wear mechanisms and wear resistance of austempered ductile iron in reciprocal sliding contact
, 2022 Austempered ductile irons (ADIs) are used in applications commonly exposed to severe contact conditions, and as a consequence wear damage frequently followed by failure of components.
Bergström, Jens +5 more
core +1 more source
Wear maps for TiC composite based coatings deposited on 303 stainless steel
, 2014 Dry sliding wear (pin-on-disc) tests were carried out under ambient conditions at room temperature for TiC coated and uncoated 303 stainless steel, using alumina as a counterface.
Rasool, Ghulam +3 more
core +1 more source
Friction behavior of laser cladding magnesium alloy against AISI 52100 steel [PDF]
, 2012 The use of magnesium alloys in engineering applications is becoming increasingly important as a relatively low density allows savings in energy consumption and therefore reduction in air pollution.
J.E. Masse +3 more
core +1 more source
Applications of CrAlN ternary system in wood machining of Medium Density Fibreboard (MDF) [PDF]
, 2009 Nowadays, medium density fibreboard (MDF) composite wood is more and more used in the furniture industry to replace bulk wood such as oak, beech, etc. Indeed, this material presents good mechanical properties, is easy to machine, homogeneous, exists in ...
Marchal, R. +10 more
core +1 more source
Lubricated sliding wear behaviour of aluminium alloy composites
, 2005 Interest in aluminium alloy (Al-alloy) composites as wear resistant materials continues to grow. However, the use of the popular Al-alloy-SiC composite can be limited by the abrasive nature of the SiC, leading to increased counterface wear rates.
Rainforth, W.M., Jones, H., Walker, J.C.
core +1 more source
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source