Results 51 to 60 of about 110,539 (317)

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Wear Measuring and Wear Modelling Based on Archard, ASTM, and Neural Network Models

, 2015
The wear measuring and wear modelling are a fundamental issue in the industrial field, mainly correlated to the economy and safety. Therefore, there is a need to study the wear measurements and wear estimation.
Pislaru, Crinela, Shebani, Amer, A. Shebani, C. Pislaru   +3 more
core   +1 more source

Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann, Berend Denkena, Hilke Petersen, Florian Schaper   +3 more
wiley   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

Breaking through the strength-ductility trade-off of LPBF-produced Ti-xNb alloys from mixed powders via ω-phase induced heterostructure

International Journal of Extreme Manufacturing
Ti- x Nb alloys produced by laser powder bed fusion (LPBF) from mixed powder usually exhibit an inhomogeneous elemental distribution, leading to a deterioration in mechanical properties.
Jian-Bo Jin, Shengfeng Zhou, Huan Yang, Junjie Yang, Zhiguo Zhang, Baisong Guo, Lai-Chang Zhang   +6 more
doaj   +1 more source

Microstructure and Performance Research on Ceramic-Enhanced Inconel 718 Matrix Composite Using Laser Additive Manufacturing

Metals, 2023
This article presents a 95% IN718 + 5% (75% Cr2O3 + TiO2) ceramic coating on the SS316L substrate surface with laser additives. The macro shape, phase, microstructure, interface, wear resistance and tensile resistance of metal base composite materials ...
Qingtao Yang, Zewei Xu, Liangliang Li, Pengfei Li   +3 more
doaj   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source

Dynamic evolution of interface roughness during friction and wear processes [PDF]

, 2014
Dynamic evolution of surface roughness and influence of initial roughness (Sa=0.282 to 6.73 µm) during friction and wear processes has been analyzed experimentally.
Bigerelle, M., Bigerelle, M, Dubar, L., Dubois, André, L. Dubar, Mathia, T., Kubiak, KJ, Dubois, A, K.J. Kubiak, M. Bigerelle, Mathia, TG, Mathia, T. G., Dubois, A., Bigerelle, Maxence, Dubar, Laurent, Kubiak, Krzysztof, T.G. Mathia, Dubar, L, Kubiak, K. J., A. Dubois   +19 more
core   +1 more source

RESISTANCE OF COATED ELECTRODES SUITABLE FOR RENOVATION OF TILLAGE TOOLS [PDF]

Journal of Central European Agriculture, 2013
This article deals with the abrasive wear resistance of additional materials. The resistance of individual materials was figured out by determining a proportional wear resistance on a grinding fabric.
Martin Kotus , Tomáš Pauliček , Tomáš Holota   +2 more
doaj   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source