Results 21 to 30 of about 19,666 (292)
Metals, 2016 This article examines the weldability of ductile cast iron when the root weld is applied with a tungsten inert gas (TIG) welding process employing an Inconel 625 source rod, and when the filler welds are applied with electrodes coated with 97.6% Ni.
Francisco-Javier Cárcel-Carrasco +3 more
doaj +1 more source
Metals, 2023 This study reports the welded joint of a novel 590 MPa V-N microalloyed wheel steel on microstructure and mechanical properties after flash butt welding.
Cairu Gao +7 more
doaj +1 more source
Review of the weldability window in explosive welding processes
Journal of Alloys and Metallurgical SystemsExplosive welding is a solid-state joining technique that employs explosive energy to propel the flyer plate into oblique collision with the base plate, forming a metallurgical bond at the interface. The process parameters, such as the loading ratio, the
Bir Bahadur Sherpa, S. Saravanan
doaj +1 more source
Microstructural and Corrosion Properties of Cold Rolled Laser Welded UNS S32750 Duplex Stainless Steel [PDF]
, 2018 The main goal of this work was to study the effect of plastic deformation on weldability of duplex stainless steel (DSS). It is well known that plastic deformation prior to thermal cycles can enhance secondary phase precipitation in DSS which can lead to
B\uf6gre, Balint +5 more
core +1 more source
Effect of aluminium sheet surface conditions on feasibility and quality of resistance spot welding [PDF]
, 2010 A study investigating the effect of sheet surface condition on resistance spot welding (RSW) of aluminium has been carried out. This concentrates on two automotive aluminium alloys; AA5754 and AA6111, used for structural and closure applications ...
Briskham +14 more
core +1 more source
Quality-weld parameters for microwelding techniques and equipment [PDF]
, 1969 Limited-amplitude, controlled-decay process improves the reliability of microwelding. The system consists in building a capacitor-discharge welder for control of the shape of the weld pulse.
Hall, L. G., Hutchinson, W. R.
core +1 more source
Advanced Engineering Materials, EarlyView.Microstructural evolution and hardness optimization along the cross‐section of friction stir welded AA6061/AlSi10MgMn joints, for electric vehicle battery housings, were investigated. Postweld aging between 170°C and 220°C enhances hardness uniformity within the nugget zone.
Emanuele Ghio, Emanuela Cerri
wiley +1 more source
Effect of the Initial Grain Size on Laser Beam Weldability for High-Entropy Alloys
Crystals, 2022 This study investigated the effect of the initial grain size on the laser beam weldability of CoCrFeMnNi high-entropy alloys (HEAs). Cold-rolled, annealed, and cast HEAs with different initial grain sizes exhibited clear differences in weldability.
Cheolho Park +4 more
doaj +1 more source
Gas metal arc welding of modified X2CrNi12 ferritic stainless steel [PDF]
, 2007 X2CrNi12 ferritic stainless steel is a low cost stainless steel grade exhibiting good corrosion and abrasion resistance. Typical applications for this steel are bus frames and chassis, railway wagons for coal and iron ore, mining and mineral processing ...
Deleu, E. +3 more
core +1 more source
CO2 laser beam welding of AM60 magnesium-based alloy [PDF]
, 2010 The authors are grateful to FONDERIE MESSIER HONSEL group that provided the as-cast magnesium alloy workpieces. The authors would like also to acknowledge the technical support of Dr.
BARRALLIER, Laurent +4 more
core +5 more sources