Results 211 to 220 of about 753,126 (286)

Optimizing Process Parameters in Laser Transmission Welding Solid PC/Porous-PET Using Prediction Models: Experimental Validation and Morphology Analysis. [PDF]

Materials (Basel)
Li J, Wu Y, Luo X, Zhou S, Wang Z, Zhang H, Zhong B, Qiao H.   +7 more
europepmc   +1 more source

Effect of External Restraints on Welding Deformation for Multi-Layer Welding

Preprints of the National Meeting of JWS, 2009
Kamitani, Keisuke, Terasaki, Toshio, Imamura, Hiroyuki   +2 more
openaire   +1 more source

Insights Into Paint‐Bake Toughening of Resistance Spot Welds of a 2.0 GPa Warm‐Stamped Medium‐Mn Steel

steel research international, EarlyView.
Paint baking of resistance spot welded joints of 2.0 GPa warm‐stamped medium‐Mn steel activates low‐temperature tempering, forming fine cementite in the fusion zone and enhancing toughness. Crack propagation resistance increases, shifting the failure mode from partial interfacial to complete pullout, with peak load and energy absorption rising ...
Sunusi Marwana Manladan, Savyasachi Nellikode, YeoJin Jang, Sumin Lee, Dileep Chandran Ramachandran, Sung‐bo Heo, Jinyoung Lee, Young‐Kook Lee, Yeong‐Do Park   +8 more
wiley   +1 more source

Hot Deformation Behavior, Dynamic Recrystallization and Phase Transformation Mechanism of Zr-Nb Alloy During Compression Processing. [PDF]

Materials (Basel)
Bi Y, Li Y.
europepmc   +1 more source

Influence of Welding Sequence on Inherent Strain and Welding Deformation Analysis

Preprints of the National Meeting of JWS, 2012
Tadano, Satoshi, Nakatani, Yujiro, Tanaka, Akira   +2 more
openaire   +1 more source

Crash Behavior of DP800–DP1000 Advanced High‐Strength Steel’s Dissimilar Resistance Spot Welded Joints Under Quasi‐static and High Strain Rates

steel research international, EarlyView.
The high‐strain‐rate behavior of resistance spot‐welded DP800–DP1000 joints is investigated. Results show that microstructural gradients across BM–HAZ–FZ govern hardness, strain rate sensitivity, and failure modes. While strength increases with strain rate, energy absorption is controlled by ductility, with DP800–DP800 joints showing superior ...
Pankaj Shrivastava, Velaphi Msomi
wiley   +1 more source

Local Yield Stress Distribution of HDPE Pipe Butt Fusion Joints Measured by a Small Punch Test. [PDF]

Polymers (Basel)
Bai C, Duan X, Hu Z, Lai HS, Zhong Y, Du P.   +5 more
europepmc   +1 more source

Influence of various factors on welding deformation during butt welding

Preprints of the National Meeting of JWS, 2013
HAMADA, Masaki, KON, Satoshi, IKUSHIMA, Kazuki, ITOH, Shinsuke, Kawahara, Atsushi, Shibahara, Masakazu   +5 more
openaire   +1 more source

Tailored Hardening and Isothermal Bainitizing of Additively Manufactured Nitrogen‐Enhanced Martensitic Chromium Steel

steel research international, EarlyView.
Tailored heat treatments transform additively manufactured high‐nitrogen martensitic Cr steel from austenitic as‐built condition to high‐hardness states. Isothermal bainitizing at 250°C generates an ultrafine nanostructure and achieves higher hardness than conventional hardening and tempering, highlighting a promising postprocessing route for laser ...
Philip König, Sebastian Weber, Jonathan Lentz   +2 more
wiley   +1 more source