Results 41 to 50 of about 532,635 (266)

Process Performance of High Energy Wire EDM

Procedia CIRP, 2021
Published by Elsevier, Amsterdam [u.a.]
Küpper, Ugur, Herrig, Tim, Welling, D., Bergs, Thomas   +3 more
openaire   +2 more sources

A brief review on the status of machining technology of fir-tree slots on aero-engine turbine disk

Advances in Mechanical Engineering, 2022
The machining precision and its consistency of turbine disk fir-tree slots have a direct influence on the performance of aero-engine rotor components. However, the structural dimensions of fir-tree slot are small, and the cutting performance of materials
Yu Jianhua, Li Xun, Zhao Wenshuo, Qin Bin, Zhang Yu   +4 more
doaj   +1 more source

Optimisation of Electrical Discharge Machining Processing for AZ91 Magnesium Alloy using Coupled AHP-Taguchi Analyses-GA Method with the Rank Selection Approach

Journal of Applied Science & Process Engineering, 2023
Despite being contemporary, the wire electrical discharge machining (EDM) industry is burdened with complicated and challenging problems. However, the double optimisation method involving Taguchi analyses and genetic algorithms is a powerful tool to ...
Meshach Chukwuebuka Ikedue, John Rajan, Sunday Oke, Ebun Fasina, Babatunde Alade Sawyerr, Wasiu Oyediran Adedeji   +5 more
doaj   +1 more source

Residual stress measurement round robin on an electron beam welded joint between austenitic stainless steel 316L(N) and ferritic steel P91 [PDF]

, 2017
This paper is a research output of DMW-Creep project which is part of a national UK programme through the RCUK Energy programme and India's Department of Atomic Energy.
A.K. Bhaduri, A.N. Forsey, ASTM, Bouchard, C.E. Truman, Chetal, D.J. Smith, Dai, EDF, Evans, F. Hosseinzadeh, Fitzpatrick, Fitzpatrick, H.C. Dey, Holden, Hosseinzadeh, Hosseinzadeh, ISO, ISO/TS 21432, J.A. Francis, Javadi, Javadi, Javadi, Javadi, Javadi, K. Abburi Venkata, Kartal, Kerr, Leggatt, M.C. Smith, Mahmoudi, Moat, N. Naveed, Naveed, Noyan, Olabi, Olabi, P.J. Bouchard, Pagliaro, Pagliaro, Prime, Prime, R.A. Ainsworth, Rossini, S. Gungor, S. Mahadevan, Schajer, Shan, Traore, Traore, Vasileiou, Vasileiou, Venkata, Venkata, VEQTER, Withers, Y. Javadi, Yaghi, Zhang   +57 more
core   +3 more sources

MULTI-PARAMETRIC OPTIMIZATION OF WIRE-EDM MACHINING ON ARTIFICIALLY-AGED AL6061/B4C COMPOSITE USING RSM AND GREY RELATIONAL ANALYSIS

Journal of Applied Engineering Science, 2023
Wire-electric discharge machining (W-EDM) is an advanced technology used for machining hard-to-cut materials with high hardness. Therefore, it is critical to characterize and model the Wire-ED machining performance for new materials having remarkable ...
S. K. Bhat, Shreyas D Sai, G. M. C., D. Doreswamy   +3 more
semanticscholar   +1 more source

Optimization Performance Parameters of OHNS Die Steel using Dimensional Analysis Intergrated with Desirability Function [PDF]

International Journal of Industrial Engineering and Production Research, 2019
In the Wire EDM of oil hardening die steel materials is a complicated machining process. Hence to find out the best set of process parameters is an important step in wire EDM process.
Mangesh Phate, Shraddha Toney, Vikas Phate   +2 more
doaj   +1 more source

Design of an electrochemical micromachining machine [PDF]

, 2014
Electrochemical micromachining (μECM) is a non-conventional machining process based on the phenomenon of electrolysis. μECM became an attractive area of research due to the fact that this process does not create any defective layer after machining and ...
A Muetze, A Spieser, AB Kamaraj, AB Kamaraj, AL Trimmer, Alexandre Spieser, Atanas Ivanov, AW Labib, B Bhattacharyya, BJ Park, C-T Lin, D Huo, DS Bilgi, ES Lee, G Skrabalak, HS Shin, J Kozak, J Kozak, JA McGeough, KP Rajurkar, KP Rajurkar, L Cagnon, M Datta, M Kock, M Sen, M Wang, MAH Mithu, MAH Mithu, PT Stanev, R Schuster, S Burkert, TKKR Mediliyegedara, U Çaydaş, V Kirchner, X Lu, X Luo, Y Lu, YJ Zhang, Z Zhang, Z Zhang, Z-W Fan   +40 more
core   +1 more source

Optimization of Wire EDM Process Parameters on Cutting Inconel 718 Alloy with Zinc-Diffused Coating Brass Wire Electrode Using Taguchi-DEAR Technique

Coatings, 2022
Inconel 718 alloy has a wide range of applications in the aerospace sector because of its superior mechanical properties and its weldability. The machining of such higher strength materials with complex shapes is possible with wire electrical discharge ...
Li-jun Liu, M. Thangaraj, P. Karmiris-Obratański, Yuanhua Zhou, Ramamurthy Annamalai, R. Machnik, A. Elsheikh, A. Markopoulos   +7 more
semanticscholar   +1 more source

Performance Investigation of Wire EDM Process Parameters

IOP Conference Series: Materials Science and Engineering, 2022
AbstractIt is exceptionally difficult to create confusing geometry in such a material using traditional machining measurement. At present, companies use a non-regular machining strategy which uses energies like electricity, chemical, sound, light, etc. which are useful for machining hard materials.
Waddah Mohamedosman Elyass, Vishal Sharma, Ganesh Kantak, Mohd Mukhtar Alam   +3 more
openaire   +1 more source

Effect of wire EDM conditions on generation of residual stresses in machining of aluminum 2014 T6 alloy

Alexandria Engineering Journal, 2016
Wire electrical discharge machining (EDM) possesses many advantages over the conventional manufacturing process. Hence, this process was used for machining of all conductive materials; especially, nowadays this is the most common process for machining of
Pujari Srinivasa Rao, Koona Ramji, Beela Satyanarayana   +2 more
doaj   +1 more source