Results 51 to 60 of about 17,542 (223)

Optimization of Process Parameters in WEDM by using Taguchi Method [PDF]

, 2016
This research represents the parametric optimization of Wire EDM on machining die steel DC53. The objective of the present work was to investigate the effects of the various Wire EDM process parameters using Taguchi on the machining quality and to obtain
Ahlawat, A. (Amit), Jain, S. (Sumit), Kumar, S. (Suresh), Rani, P. (Preety)   +3 more
core  

Study of Fine-Finish Wire EDM

Journal of The Japan Society of Electrical Machining Engineers, 2011
In this paper, methods of obtaining fine-finish surfaces in wire electrical discharge machining are discussed. Some countermeasures to reduce the stray capacitance of wire EDM, which restricts the surface roughness on an EDMed surface, are described. A surface roughness of 0.6[μm] Rz is obtained using a 0.1[μs] pulse width group type AC pulse generator.
Kei SHISHIHARA, Haruki OBARA, Ikkou MATSUBARA, Tohru SASAKI   +3 more
openaire   +2 more sources

Precisely process of Wire Electrode EDM.

Journal of The Japan Society of Electrical Machining Engineers, 1985
This paper has been described precisely process of Wire Electrode EDM.First chapter, we describe introduction on this paper.After of second chapter, we describe relation between wire bending and wire tension, residual stress of tungsten wire, shape of chip in the water, relation between tension fluctuate and deflection of wire, and locus compensation ...
Iwao KONDO, Kiyoshi NISHIMOTO
openaire   +2 more sources

A Bibliometric Analysis of Process Mining

WIREs Data Mining and Knowledge Discovery, Volume 16, Issue 2, June 2026.
Process mining studies with numbers. ABSTRACT Process mining (PM) has emerged as a pivotal discipline in data science, bridging traditional process analysis with data‐driven techniques to extract actionable insights from event logs. This study conducts a comprehensive bibliometric analysis of 1764 peer‐reviewed articles from the Web of Science database
Seyfullah Tokumaci, Onur Dogan, Oguzhan Ozturk   +2 more
wiley   +1 more source

Prediction and optimization of surface quality and material removal rate in wire-EDM cutting of tungsten–copper alloy (W70Cu30)

Results in Surfaces and Interfaces
Tungsten-copper alloy (W70Cu30) is widely used in industrial applications due to its high thermal conductivity, melting point, and wear resistance. This study investigates its machinability using wire electrical discharge machining (EDM).
Abdullah Eaysin, Muhammad Ali Zinnah, Md. Nayem, Hosney Ara Begum, Md.Injamamul Haque Protyai, Salahuddin Ashrafi, Adib Bin Rashid   +6 more
doaj   +1 more source

Dry sliding friction and wear response of WC-Co hardmetal pairs in linearly reciprocating and rotating contact [PDF]

, 2011
This paper presents an experimental evaluation of friction and wear properties of WC-Co cemented carbides. A comparison is made between unlubricated rotating and linearly reciprocating pin-onplate sliding pairs. The plate specimens were WC-10wt%Co grades
Bonny, Koenraad, De Baets, Patrick, Lauwers, Bert, Malek, Olivier, Neis, Patric Daniel, Perez Delgado, Yeczain, Rodriguez Fereira, Vanessa, Vleugels, Jef   +7 more
core   +1 more source

Practical Issues in the Application of Direct Metal Laser Sintering [PDF]

, 2006
Direct Metal Laser Sintering (DMLS) was introduced to meet the objective of producing metal parts directly from CAD data. CRDM has accumulated six years of experience in applying this technique, mostly to prototyping parts for evaluation.
Bennett, G., Jacobson, D. M.
core   +1 more source

Influence of the Cr to Ti Ratio on the High‐Temperature Oxidation Behavior of TaMoCrTiAl Complex Concentrated Alloys in Nitrogen‐Free Atmospheres

Materials and Corrosion, Volume 77, Issue 3, Page 442-452, March 2026.
Ta‐Mo‐Cr‐Ti‐Al refractory high‐entropy alloys show atmosphere‐dependent oxidation performance based on Cr:Ti ratios. Cr‐rich compositions excel in dry oxygen through continuous chromia formation, while Ti‐rich alloys perform better in humid conditions due to reduced chromium volatilization and hydrogen uptake effects.
Fabian Lanoy, Emma M. H. White, Bjoern Schäfer, Chongchong Tang, Carsten Schroer, Bronislava Gorr, Mathias C. Galetz   +6 more
wiley   +1 more source

Surface and subsurface characteristics of wire-electrical discharge machined Al-alloy and composite: a fundamental study on the role of machining variables

Journal of Materials Research and Technology
For hard-to-machine materials like discontinuous particulate reinforced Al-matrix composites, wire-electrical discharge machining (wire-EDM) is increasingly preferred for manufacturing intricately shaped parts with high dimensional accuracies and surface
Gaurav Anand, Santanu Sardar, Satesh Sah, Ashim Guha, Ibrahim Albaijan, Debdulal Das   +5 more
doaj   +1 more source

Guidelines to select suitable parameters for contour method stress measurements [PDF]

, 2020
The contour method is one of the promising techniques for the measurement of residual stresses in engineering components. In this method, the cut surfaces deform, owing to the relaxation of residual stresses.
Naveed, Nida
core   +1 more source