Results 111 to 120 of about 37,330 (309)

Ti3C2Tx MXene/Silver Composite Foams For Lightweight, High‐Performance Electromagnetic Interference Shielding and Joule Heating

Advanced Materials Interfaces, EarlyView.
Ultrathin MXene/EMF composite foams achieve a specific shielding efficiency of 749.6 dB.dB·cm3$\mathrm{dB}\cdot {\mathrm{cm}}^{3}$/g, while the silver‐enhanced MXene/Ag/EMF reaches 81.4 dB shielding effectiveness at just 1.0 mm thickness. Both composites exhibit rapid Joule heating, retain stability up to 250∘C$^\circ{\rm C}$, and withstand 1000 ...
Abdullah A. Mahmood, Mingxuan Li, Vahid Rad, Mehdi Zarei, Chen‐Yu Yeh, Masoud Soroush, Guangyong Li, Paul W. Leu   +7 more
wiley   +1 more source

Tangential and radial deformation field measurements on wood during drying

, 1997
In a previous study, the deformation field measurement method on wood during drying was described. This paper discusses the deformation field measurement results during drying to 8.2% moisture content on the radial and tangential surfaces.
Kifetew, Girma,, Wiklund, Martin,, Lindberg, Henrik,   +2 more
core   +2 more sources

Monitoramento do teor de umidade de madeiras de Pinus elliottii Engelm. E Eucalyptus grandis W. Hill ex Maiden, sob diferentes temperaturas de secagem, através do ultra-som

Ciência Florestal, 2007
With the purpose of evaluating the viability of use of ultrasonic technique to estimate the wood moisture content during the drying process, samples of Pinus elliottii Engelm. and Eucalyptus grandis W. Hill ex Maiden with dimensions of 3.5 cm thick, 10
Leandro Calegari, Diego Martins Stangerlin, Elio José Santini, Clovis Roberto Haselein, Solon Jonas Longhi, Paulo Inácio Obregon do Carmo, Luiz Carlos Pinto da Silva, Darci Alberto Gatto   +7 more
doaj  

Additive Manufacturing of Patient‐Specific Intracranial Aneurysm Cell Culture Models

Advanced Materials Technologies, EarlyView.
Patient‐specific intracranial aneurysm models were fabricated using chocolate moulding, 3D printed water‐soluble cores, and direct resin 3D printing. Moulding PDMS around sacrificial cores made of chocolate or 3D printed water‐soluble resin yielded accurate, expandable, and endothelializable models that outperformed resin‐based approaches.
Chloe M. de Nys, Jaimee‐Lee Wood, James I. Novak, Danilo Carluccio, Craig D. Winter, Ashley R. Murphy, Mark C. Allenby   +6 more
wiley   +1 more source

A Mass-Transport Model for Drying Wood under Isothermal Conditions

, 2005
Mass transport in wood during drying is often described in terms of different periods. Depending on the current moisture content (MC) and the structure of the wood, the driving forces behind the mass transport are essentially different.
Danvind, Jonas, Johansson, Håkan,, Eriksson, John,   +2 more
core  

Skin‐Like Tri‐Modal Sensors Based on Soft Piezoelectric and Ionic Composites

Advanced Materials Technologies, EarlyView.
Inspired by the multimodal perception of human skin, a soft, skin‐like tri‐modal sensor is presented. The device incorporates an ionically conductive, piezoelectric, elastic composite as its active layer, enabling independent detection of temperature, static strain, and dynamic strain within a single two‐terminal architecture.
Liren Wang, Peter Zalar, Vishva Bhate, Takeo Furukawa, Hidekazu Kodama, Yijun Liu, Yuanyuan Zhou, Chuang Hou, Siyuan Liu, Naoji Matsuhisa   +9 more
wiley   +1 more source

INFLUENCE OF TEMPERATURE ON CRACKING AND MECHANICAL PROPERTIES OF WOOD DURING WOOD DRYING – A REVIEW

BioResources, 2007
The occurrence of cracks and loss of mechanical properties are major problems in wood drying, and careful control of drying conditions is necessary in order to avoid this form of defects.
Oltean, Laura, Teischinger, Alfred, Hansmann, Christian   +2 more
doaj  

The Evolution of Aerosol Jet Printing, A Review: Enhancing Material Versatility and Improvements for Next‐Generation Applications

Advanced Materials Technologies, EarlyView.
Aerosol Jet Printing (AJP) has emerged as a versatile additive manufacturing technique for high‐resolution, conformal, and multi‐material printing. This review highlights advances in printable materials, substrate compatibility, post‐processing, characterization, and process innovations, while critically discussing current challenges and future ...
Chandrachur Chatterjee, Rocco Lupoi, Michael J. Gibbons   +2 more
wiley   +1 more source

Canadian Developments in Kiln Drying

, 2012
The objective of this paper is to summarize recent trends related to industrial kiln drying with especial emphasis on the drying of softwood dimension lumber in Canada.
Oliveira, Luiz C De S,, Elustondo, Diego, Mujundar, Arun,, Ananías, Rubén A. ,   +3 more
core   +1 more source

Advances in Electroactive Liquid Crystal Elastomers for Intelligent Robotics and Electronics

Advanced Robotics Research, EarlyView.
Electroactive liquid crystal elastomers (eLCEs) integrate molecular anisotropy with electrical functionality to enable programmable actuation and reconfigurable electronics. This review classifies eLCEs into robotic actuators and adaptive electronics, summarizes key actuation mechanisms, and highlights fabrication strategies that bridge materials to ...
Kavita Ramesh Rathod, Sena Chon, Jae Hyuk Hwang, Sung Hyuk Park, Woohwa Lee, Joonmyung Choi, Shi Hyeong Kim, Seung Hwan Ko, Changsoon Choi, Seon Jeong Kim, Dong‐Gyun Kim, Habeom Lee, Kyung Gook Cho, Woon‐Hong Yeo, Hyun Kim   +14 more
wiley   +1 more source