Results 51 to 60 of about 118,334 (258)

Simple Synthesis of Copper Oxide Nanoparticles in the Presence of Extractive Rosmarinus Officinalis leaves [PDF]

Journal of Nanostructures, 2016
In this work, copper oxide nanoparticles have been synthesized via extractive Rosmarinus Officinalis leaves by simple and economic co-precipitation method at ambient conditions which it has used (CH3COO)2Cu+H2O individually as Cu sources.
M. R. Mohammad Shafiee, M. Kargar, M. Ghashang   +2 more
doaj   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Enhancing high-energy powder X-ray diffraction applications using a PILATUS4 CdTe detector

Journal of Synchrotron Radiation
Hybrid photon counting detectors have significantly advanced synchrotron research. In particular, the introduction of large cadmium telluride-based detectors in 2015 enabled a whole new range of high-energy X-ray measurements.
Tilman Donath, Sofia Trampari, Lucas Wagner, Mads R. V. Jørgensen, Frederik H. Gjørup, Stefano Checchia, Marco Di Michiel, Emmanuel Papillon, Gavin Vaughan   +8 more
doaj   +1 more source

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source

Why do we need a(nother) new data format? A standardized data format for azimuthally integrated area detector data

Journal of Synchrotron Radiation
Many powder X-ray diffraction, total scattering, and small-angle X-ray scattering experiments at synchrotron facilities yield azimuthally integrated intensity data, yet current practice relies on facility-specific data formats that hinder inter ...
Mads Ry Vogel Jørgensen, Frederik Holm Gjørup, Meghdad Yazdi-Rizi, Zdenek Matej, Wout De Nolf, Paul Bell   +5 more
doaj   +1 more source

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source

Review - X-ray diffraction measurements in high magnetic fields and at high temperatures

Science and Technology of Advanced Materials, 2009
A system was developed measuring x-ray powder diffraction in high magnetic fields up to 5 T and at temperatures from 283 to 473 K. The stability of the temperature is within 1 K over 6 h.
Yoshifuru Mitsui, Keiichi Koyama and Kazuo Watanabe
doaj  

Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys

Advanced Engineering Materials, EarlyView.
An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi, Mathias Galetz, Georg Hasemann, Fabian Lanoy, Emma White, Manja Krüger   +5 more
wiley   +1 more source

Semantic Modeling in Materials Science and Engineering With Platform MaterialDigital Core Ontology 3.0

Advanced Engineering Materials, EarlyView.
The community‐driven Platform MaterialDigital Core Ontology (PMDco) 3.0 is introduced as a Basic Formal Ontology‐aligned semantic backbone for the processing–structure–properties paradigm in Materials Science and Engineering. Modular engineering, automated releases, and validation workflows are highlighted and key semantic patterns for materials ...
Markus Schilling, Philipp von Hartrott, Jörg Waitelonis, Thomas Hanke, Henk Birkholz, Hossein Beygi Nasrabadi, Khashayar Razghandi, Kamilla Zaripova, Felix Thonagel, Fabian Neuhaus, Martin Glauer, Lars Vogt, Harald Sack, Lutz Mädler, Bernd Bayerlein, Chris Eberl   +15 more
wiley   +1 more source

The Influence of Field‐Assisted Sintering Technology (FAST) Temperature and Cooling Rate on the Microstructural Evolution in Gamma‐Titanium Aluminide Alloy GE4822

Advanced Engineering Materials, EarlyView.
Controlling the Field Assisted Sintering Technology (FAST) parameters, dwell temperature and cooling rate, significantly influences the microstructural evolution in titanium aluminide GE4822. Significant γ‐lamellar colonies develop only upon cooling through the α‐transus.
Jack Krohn, James Pepper, Martin Jackson
wiley   +1 more source