Results 91 to 100 of about 31,774 (223)
Düzce Üniversitesi Bilim ve Teknoloji Dergisi, 2018 Bu çalışmada, östenitik paslanmazçelik (AISI 304) ve düşük karbonlu çelik (S235JR) malzemenin gaz metal arkkaynak yöntemi kullanılarak farklı akım-voltaj (kaynak enerjisi) değerleri vetel besleme hızlarında kaynak edilebilirliği araştırılmıştır ...
Muhammet Hüseyin Çetin +3 more
doaj +1 more source
Materials Research Express, 2020 At room temperature, the hollow shaft of AISI 304 stainless steel tubes was produced by a hydraulic bulging process. The behavior of strain-induced austenite to martensite transformation and the twin crystallographic nature of AISI 304 stainless steel ...
G S Song, K S Ji, H W Song, S H Zhang
doaj +1 more source
Application of the linear matching method to creep-fatigue failure analysis of cruciform weldment manufactured of the austenitic steel AISI type 316N(L) [PDF]
, 2012 This paper demonstrates the recent extension of the Linear Matching Method (LMM) to include cyclic creep assessment [1] in application to a creep-fatigue analysis of a cruciform weldment made of the stainless steel AISI type 316N(L). The obtained results
Chen H. F., H. Chen, Y. Gorash
core +1 more source
steel research international, Volume 97, Issue 2, Page 955-966, February 2026.This study investigates how drawing process parameters affect the tribological behavior of AISI 304 steel sheet. Under lubricated conditions, increasing normal force, drawing speed, and countersamples roughness reduces the coefficient of friction by up to 21%.
Felipe de Souza Leal +6 more
wiley +1 more source
FRICTION WELDING OF DISSIMILAR AISI 304 AND AISI 8640 STEELS
, 2016 This study investigates the joinability of AISI 8640 heat treatable steel and AISI 304 austenitic stainless steel combined with friction welding. These steels have completely different properties and widely used in industrial applications. Welding is applied on steels with the parameters of 1800 rev/min turning speed, 50 MPa friction pressure and 2, 4,
BATI, Serkan +2 more
openaire +4 more sources
Frictional and structural characterization of ion-nitrided low and high chromium steels [PDF]
Low Cr steels AISI 41410, AISI 4340, and high Cr austenitic stainless steels AISI 304, AISI 316 were ion nitrided in a dc glow discharge plasma consisting of a 75 percent H2 - 25 percent N2 mixture.
Spalvins, T.
core +1 more source
Evaluation of residual stress relaxation and its effect on fatigue strength of AISI 316L stainless steel ground surfaces: Experimental and numerical approaches [PDF]
, 2013 This paper is aimed at evaluating the residual stress relaxation and its effect on the fatigue strength of AISI 316L steel ground surfaces in comparison to electro-polished surfaces.
BRAHAM, Chedly +2 more
core +2 more sources
Egyptian Journal of Petroleum, 2015 In this study, the effect of solution pH on the electrochemical behaviour of AISI 304 austenitic and AISI 430 ferritic stainless steels at open circuit potential (OCP) in concentrated acidic solutions was studied.
A. Fattah-alhosseini, S. Vafaeian
doaj +1 more source
Strengthening of stainless steel weldment by high temperature precipitation
Journal of Materials Research and Technology, 2017 The mechanical behavior and the strengthening mechanism of stainless steel welded joints at 600 °C have been investigated. The welds were composed of AISI 304 stainless steel, as base metal, and niobium containing AISI 347 stainless steel, as weld metal.
Sergio Neves Monteiro +5 more
doaj +1 more source
Electrochemical synthesis of peroxomonophosphate using boron-doped diamond anodes [PDF]
, 2008 A new method for the synthesis of peroxomonophosphate, based on the use of boron-doped diamond electrodes, is described. The amount of oxidant electrogenerated depends on the characteristics of the supporting media (pH and solute concentration) and on ...
E. Weiss +45 more
core +2 more sources