Results 71 to 80 of about 2,053 (178)
Düzce Üniversitesi Bilim ve Teknoloji Dergisi, 2018 Bu çalışmada, östenitik paslanmazçelik (AISI 304) ve düşük karbonlu çelik (S235JR) malzemenin gaz metal arkkaynak yöntemi kullanılarak farklı akım-voltaj (kaynak enerjisi) değerleri vetel besleme hızlarında kaynak edilebilirliği araştırılmıştır ...
Muhammet Hüseyin Çetin +3 more
doaj +1 more source
Materials Research Express, 2020 At room temperature, the hollow shaft of AISI 304 stainless steel tubes was produced by a hydraulic bulging process. The behavior of strain-induced austenite to martensite transformation and the twin crystallographic nature of AISI 304 stainless steel ...
G S Song, K S Ji, H W Song, S H Zhang
doaj +1 more source
Наука и техникаThis paper presents the results of a study on the effect of Electrolytic-Plasma Treatment (EPT) parameters on the structure and properties of the surface layer of austenitic corrosion-resistant steels AISI 304, AISI 316L, and AISI 321, which are widely ...
A. Yu. Korolyov +3 more
doaj +1 more source
Strengthening of stainless steel weldment by high temperature precipitation
Journal of Materials Research and Technology, 2017 The mechanical behavior and the strengthening mechanism of stainless steel welded joints at 600 °C have been investigated. The welds were composed of AISI 304 stainless steel, as base metal, and niobium containing AISI 347 stainless steel, as weld metal.
Sergio Neves Monteiro +5 more
doaj +1 more source
International Journal of Electrochemical Science, 2012 The metallic carbide precipitation was observed after the sensitization of AISI 304 stainless steel specimens in neutral flame by using oxy-fuel and slowly cooled in the air.
Mohd Warikh Abd Rashid +3 more
doaj +1 more source
Egyptian Journal of Petroleum, 2015 In this study, the effect of solution pH on the electrochemical behaviour of AISI 304 austenitic and AISI 430 ferritic stainless steels at open circuit potential (OCP) in concentrated acidic solutions was studied.
A. Fattah-alhosseini, S. Vafaeian
doaj +1 more source
AISI 304 ve AISI 316 Östenitik Paslanmaz Çeliklerin İşlenebilirliğinin Değerlendirilmesi
El-Cezeri Fen ve Mühendislik Dergisi, 2015 Bu calismada AISI 304 ve AISI 316 ostenitik paslanmaz celiklerin islenebilirligini degerlendirmek amaciyla kaplamasiz tungsten karbur kesici takimlar kullanilarak bir takim tornalama deneyleri yapilmistir. Deneyler, kuru kesme sartlarinda sabit kesme derinligi (2,4 mm), dort kesme hizi (100, 120, 140 ve 160 m/dak) ve uc ilerleme hizinda (0,15, 0,3 ve 0,
ALTAN ÖZBEK, Nuırsen +3 more
openaire +4 more sources
International Journal of Electrochemical Science, 2018 As a new developed shot peening technology, wet micro shot peening is applied to investigate the influence on corrosion behavior of AISI 304 stainless steel in chloride solution using potentiodynamic polarization.
Xinlong Wei +4 more
doaj +1 more source
Laser decoration of AISI 304 steel surface
Technologies & QualityThe influence of laser marking parameters on the decorative characteristics of AISI 304 steel surface was investigated. Changes in roughness (Ra, Rz) and local colour (LC) (averaged RGB value) were studied as a function of laser radiation power, scanning speed, and resolution (linear pulse density).
Denis M. Tsvetkov +2 more
openaire +1 more source
Materials Research, 2009 Mechanical and tribological properties os AISI 304 and AISI 316 stainless steels submited to glow discharge ion nitriding are reported.The atmosphere was 20:80 - N2:H2 with substrate temperatures ranging from 300 to 500 °C.
Fabiana Cristina Nascimento +5 more
doaj +1 more source