Results 61 to 70 of about 31,774 (223)
Ніобієвий катод для електрохімічного синтезу титану (III) сульфату в технології титану (IV) оксиду [PDF]
, 1972 Досліджено електродні матеріали, які мають низьку перенапругу виділення водню та кисню, високу стійкість у розчинах сульфатної кислоти, а також можуть бути перспективними для роботи при густині струму не менше 5,0 А/дм².
Федоренко, А. О. +3 more
core +1 more source
Driving forces in the corrosion dynamics of stainless steels in different aquatic environments
Materials Research ExpressCorrosion is a critical factor in maintaining the integrity of marine facilities such as ship structures, offshore platforms, and other infrastructure, as it leads to surface deformation, including cracking and pitting.
Emrah Sık
doaj +1 more source
Mechanical, Microstructure and Corrosion Properties of Friction Stir Welded Dissimilar Austenitic Stainless Steel Joints [PDF]
Materials ResearchIn many industries, challenges arise when welding dissimilar materials using traditional methods, such as fusion welding. These challenges often lead to problems like cracking, phase segregation, and intermetallic formation.
Sundar raju Govindaraj +2 more
doaj +1 more source
Urania, 2021 PERILAKU TARIK DAN STRUKTUR MIKRO BAJA TAHAN KARAT AISI 304 PASCA PERLAKUAN PANAS PADA DAERAH SENSITISASI 600 – 700 °C. Baja tahan karat AISI 304 digunakan sebagai komponen struktur reaktor daya tipe LWR.
Sungkono Sungkono, Sri Ismarwanti
doaj +1 more source
Variasi Arus Listrik Terhadap Sifat Mekanik Mikro Sambungan Las Baja Tahan Karat Aisi 304 [PDF]
, 2018 Dasar penelitian ini adalah karena baja tahan karat merupakan baja paduan tinggi, maka kualitas sambungan lasnya sangat dipengaruhi dan menjadi getas oleh panas dan atmosfer pengelasan.
Nofri, M. (Media), Yakub, Y. (Yunus)
core
Low cycle fatigue life improvement of AISI 304 by initial and intermittent wire brush hammering [PDF]
, 2013 The effects of hammering by wire brush as a method of improving low cycle fatigue life of highly ductile austenitic stainless steel AISI 304 have been investigated through an experimental study combining imposed strain fatigue tests and assessment of ...
BRAHAM, Chedly +4 more
core +3 more sources
Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution
Advanced Engineering Materials, Volume 28, Issue 8, 22 April 2026.Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat +5 more
wiley +1 more source
OPTIMIZATION OF SURFACE ROUGHNESS OF AISI 304 AUSTENITIC STAINLESS STEEL IN DRY TURNING OPERATION USING TAGUCHI DESIGN METHOD [PDF]
, 2010 The present work is concentrated with the dry turning of AISI 304 Austenitic Stainless Steel (ASS). This paper presents the influence of cutting parameters like cutting speed, feed rate and depth of cut on the surface roughness of austenitic stainless ...
D. PHILIP SELVARAJ, P. CHANDRAMOHAN
core
Engineering Reports, Volume 8, Issue 4, April 2026.Welding power and post‐weld heat treatment (PWHT) at 850°C influence phase transformations in S32205 duplex stainless steel, promoting sigma phase formation and reducing corrosion resistance. PWHT at 850°C also replicates HAZ‐like microstructures in base metal, enabling improved characterization of weld joint properties.
Sandra Chacón‐Fernández +2 more
wiley +1 more source
Journal of Materials Research and TechnologyCoCrFeNi high entropy alloy (HEA) is endowed with a series of outstanding properties, such as excellent tensile performance, good resistance to cryogenic and corrosion, due to its unique chemical composition and crystal structure. The joining of CoCrFeNi
Xueting Zhang +4 more
doaj +1 more source