Grain boundary oxidation and the chromium-depletion theory of intercrystalline corrosion of austenitic stainless steels [PDF]
, 1967 18 polymers were characterized with respect to their friction and wear behaviour in contact with steel in environments of air and water. These were six unfilled materials, i.e. polyamide 66 (PA 66), polyoxymethylene (POM), polyethyleneterephthalate (PETP)
Gellings, P.J., Jongh, M.A. de
core +8 more sources
Metals, 2020 Similar and dissimilar material joints of AISI grade 304 (1.4301) and AISI grade 316 (1.4401) austenitic stainless steel by solid state diffusion bonding and transient liquid phase (TLP) bonding are of interest to academia and industry alike. Appropriate
Abdulaziz AlHazaa, Nils Haneklaus
doaj +1 more source
Using Taguchi method to optimize welding pool of dissimilar laser welded components [PDF]
, 2008 In the present work CO2 continuous laser welding process was successfully applied and optimized for joining a dissimilar AISI 316 stainless steel and AISI 1009 low carbon steel plates. Laser power, welding speed, and defocusing distance combinations were
A.G. Olabi +16 more
core +1 more source
Effect of pulsed magnetic field pre-treatment of AISI 52100 steel on the coefficient of sliding friction and wear in pin-on-disk tests [PDF]
, 2014 Disc specimens manufactured from commercial bearing rollers (AISI 52100 steel, 62–63 HRC) in initial state and after pre-treatment by pulsed magnetic field (PMF) with a magnetic field strength of 1–7 MA/m were tested with sunflower oil using pin-on-disk ...
A A Lebedev +24 more
core +2 more sources
Mechanical Properties of Boronized AISI 316, AISI 1040, AISI 1045 and AISI 4140 Steels
Acta Physica Polonica A, 2009 In this study, some mechanical properties of borided and unborided four steels were investigated. Boronizing of steels was performed by powder pack method at 1210 K for 4 h. The hardness of borides, boride layer thickness and room temperature tensile properties were measured and it was observed that hardness and tensile properties strongly depend on ...
Sahin, O., UÇAR, Nazım, Çalık, ADNAN
openaire +3 more sources
Fiber laser-MAG hybrid welding of DP/AISI 316 and TWIP/AISI 316 dissimilar weld
Procedia CIRP, 2019 Abstract In this paper, TWinning-Induced Plasticity (TWIP), Dual Phase (DP) and austenitic stainless (AISI 316) steels were joined together by hybrid laser/arc welding with an austenitic steel filler. Microstructural and mechanical characterization of welded joints was carried out by optical microscopy, microhardness, tensile and bend tests. The heat
Casalino G. +5 more
openaire +3 more sources
Simulating the Effects of Substrate Pre-Heating on the Final Structure of Steel Parts Built by Laser Powder Deposition [PDF]
, 2004 Tool steel parts built by laser powder deposition often present a heterogeneous distribution of properties caused by the complex structural transformations that occur during the deposition process.
Costa, L., Réti, T., Vilar, R.
core +1 more source
Mechanical, Microstructure and Corrosion Properties of Friction Stir Welded Dissimilar Austenitic Stainless Steel Joints [PDF]
Materials ResearchIn many industries, challenges arise when welding dissimilar materials using traditional methods, such as fusion welding. These challenges often lead to problems like cracking, phase segregation, and intermetallic formation.
Sundar raju Govindaraj +2 more
doaj +1 more source
Physical and tribological properties of Nitrided AISI 316 stainless steel balls [PDF]
, 2016 AISI 316 austenitic stainless steel balls (diameters 5.0 and 12.0 mm, typical hardness 250 HV0.3) and flat samples (20×20×2.0 mm) were nitrided by a pulsed glow discharge Ar/N2 plasma. Hardness of the ball surfaces was analyzed using Vickers indentation.
Akinlabi +10 more
core +2 more sources
Differential mortality and wealth accumulation [PDF]
, 1995 The issue of asset accumulation and decumulation is central to the life cycle theory of consumer behavior and to many policy questions. One of the main implications of the life cycle model is that assets are decumulated in the last part of life.
Attanasio, O., Hoynes, H.W.
core +1 more source