Results 31 to 40 of about 1,212 (182)

Influence of temperature and hydrostatic pressure on the galvanic corrosion between 90/10 Cu–Ni and AISI 316L stainless steel

Journal of Materials Research and Technology, 2021
The galvanic corrosion behavior of the 90/10 Cu–Ni alloy coupled to AISI 316L stainless steel, has been studied at different temperatures (5, 15 and 30 °C) and hydrostatic pressures (0.1, 10 and 20 MPa) by electrochemical and SEM methods.
Shengbo Hu, Rui Liu, Li Liu, Yu Cui, Fuhui Wang   +4 more
doaj   +1 more source

Benchmarking Coaxial and Angular Optical Emission Spectroscopy With Recommendations for Reliable Compositional In Situ Monitoring During Laser Powder Bed Fusion

Advanced Materials Technologies, EarlyView.
ABSTRACT Real‐time insight into local chemistry is critical for reliable part quality in additive manufacturing, especially laser powder bed fusion (PBF‑LB/M), where rapid thermal cycles and localized evaporation can undermine part performance. Optical emission spectroscopy (OES) offers non‑intrusive, in situ plume monitoring, but detection geometry ...
Philipp Gabriel, Bastian Jülich, Anna Rosa Ziefuss, Florian Eibl, Stephan Barcikowski   +4 more
wiley   +1 more source

Carboxyphenolate Coordination Frameworks for High‐Voltage Calcium Storage

Advanced Science, EarlyView.
A hexaanionic carboxyphenolate coordination framework, Ca2‐M‐THBPD (M = Mg, Ca, Ba), exhibits ligand‐centered enolate‐quinonoid redox activity enabling tunable, high‐voltage Ca2+ storage (3.5 V vs Ca2+/Ca) modulated by spectator cations. The amorphous structure accommodates reversible divalent‐ion insertion, contributing to enhanced cycling stability ...
Vasudeva Rao Bakuru, Darsi Rambabu, Xiaodong Lin, Robert Markowski, Petru Apostol, Viliam Frano, Xiaolong Guo, Taniya Purkait, Shubhadeep Pal, Tom Goossens, Da Tie, Augustin Ramackers, Alexandru Vlad   +12 more
wiley   +1 more source

Comparison of cavitation erosion of NiCrBSi and AISI 316L coatings deposited by powder plasma transferred Arc welding

Acta Polytechnica
This study carefully compares the effect of microstructure and hardness on the cavitation wear resistance of PPTA (Powder Plasma Transferred Arc) deposited coatings. Deposits were made on a substrate of S235JR structural steel.
Weronika Henzler, Mirosław Szala, Tomasz Pałka, Bernard Wyględacz, Artur Czupryński, Leszek Łatka   +5 more
doaj   +1 more source

Reverse Engineering and Performance Evaluation of a Pump Impeller Fabricated With Additive Manufacturing

Chemie Ingenieur Technik, EarlyView.
This study explores the process chain for reverse engineering and additive manufacturing of a water pump impeller in a process plant. Key aspects include digital twin creation, CAD redesign, material certification, Hirtisation postprocessing, and performance testing. Insights highlight iterative design for improved precision and reliability.
Michael Stadler, Kati Schatz, Sebastian Rehfeldt, Harald Klein   +3 more
wiley   +1 more source

INCIDENCE OF HEAT TREATMENT ON THE CORROSIVE BEHAVIOR OF AISI 316L AUSTENITIC STAINLESS STEEL

Acta Metallurgica Slovaca, 2023
Heat treatments of AISI 316L samples were conducted at 900°C with slow cooling in air to induce varied precipitation of chromium-rich carbide particles at grain boundaries, resulting in a microstructure susceptible to intergranular corrosion. The corrosion behavior of the material in this state was investigated in a salt spray chamber containing 5 ...
Mariano Nicolás Inés, Graciela Analía Mansilla   +1 more
openaire   +2 more sources

PERBAIKAN KUALITAS MATERIAL STAINLESS STEEL 316L PADA APLIKASI IMPLAN PENYAMBUNG TULANG DENGAN MENGGUNAKAN METODE DEFORMASI DINGIN, ANNEALING STRESS RELIEF, DAN SANDBLASTING

Rekayasa, 2012
Material implan merupakan produk yang dibuat dengan tujuan untuk untuk membantu fiksasi, perbaikan, penggantian bagian tulang yang retak atau patah pada tubuh manusia.
Mirza Pramudia
doaj   +1 more source

Analysis of Corrosion and Wall Perforation in the Heat Exchanger Made of AISI 316L Stainless Steel

Materials and Corrosion, EarlyView.
Elevated passivation temperature is identified as the dominant factor triggering localized corrosion and subsequent perforation of AISI 316L heat exchanger tubes. Electrochemical and complementary characterization results show that the alloy retains high resistance to general, pitting, and intergranular corrosion, indicating that failure primarily ...
Bojana Radojković, Bore Jegdić, Branimir Grgur, Stefan Dikić, Jovanka Pejić, Anđela Simović, Nataša Gajić, Aleksandra Popović   +7 more
wiley   +1 more source

Parametric studies of dissimilar welding of AISI 409 ferritic stainless steel to AISI 316L austenitic stainless steel using Taguchi desirability analyses

Journal of the Mechanical Behavior of Materials, 2018
In the present work, dissimilar joints between AISI 409 ferritic stainless steel and AISI 316L austenitic stainless steel were made by gas metal arc welding (GMAW) using ESAB AUTO Rod 316L as a filler wire.
Ghosh Nabendu, Pal Pradip Kumar, Nandi Goutam   +2 more
doaj   +1 more source

Tailoring Laser Powder Bed Fusion and Post‐Processing Parameters for JIS SKD61 Tool Steels: Surface Roughness, Microstructure, and Mechanical Properties

steel research international, EarlyView.
Laser powder bed fusion of JIS SKD61 tool steel is systematically optimized using a Taguchi design and ANOVA. Hatch spacing and layer thickness are identified as dominant parameters controlling surface roughness and tensile strength. Subsequent tempering at 600°C improves microstructural stability and mechanical performance, enabling high‐density SKD61
Masrurotin Masrurotin, Andi Ard Maidhah, Maziar Ramezani, Wojciech Macek, Cho‐Pei Jiang   +4 more
wiley   +1 more source