Surface integrity optimization for ball-end hard milling of AISI D2 steel based on response surface methodology. [PDF]
PLoS ONE, 2023 This study focuses on systematically revealing how cutting parameters influence the surface integrity of ball-end hard milled surface of AISI D2 steel and proposing optimization scheme from surface integrity, wear resistance and fatigue resistance ...
Weimin Huang +3 more
doaj +2 more sources
Surface Integrity in the Grinding of Hardened AISI D2 Steel. [PDF]
Materials (Basel)The surface integrity of grinding has a significant influence on the service performance and life of machined parts. In this study, the influence of grinding parameters and the grit size of the grinding wheel on the surface integrity of the hardened steel, including the roughness, microstructure, and hardness of the subsurface and the residual stress ...
Zhang T +8 more
europepmc +3 more sources
Machinability Evaluation in Hard Milling of AISI D2 Steel [PDF]
Materials Research, 2016 Milling of hardened steel components provides considerable benefits in terms of reduced manufacturing cost and time compared to traditional machining. Temperature variation in milling is an important factor affecting the wear of cutting tools.
Vinayak Neelakanth Gaitonde +4 more
doaj +5 more sources
Effect of Post-Heat Treatment on the Impact Toughness and Crack Propagation Mechanism of AISI D2 Tool Steel Manufactured by Direct Energy Deposition [PDF]
Archives of Metallurgy and Materials, 2023 This study investigated the effect of heat treatment on the microstructure and impact toughness property of AISI D2 manufactured with direct energy deposition (DED) and compared the results with conventional wrought material.
Jung-Hyun Park +5 more
doaj +1 more source
Comparison of surface characteristics and micro hardness of AISI D2 tool steel and LM13 aluminum alloy machined under dry EDM (green machining) process [PDF]
FME Transactions, 2021 In this experimental work, the micro structure and the micro hardness of the surfaces machined under the dry EDM process is analyzed for AISI D2 tool steel and LM13 aluminum alloy. The experiments were conducted using copper tool electrode.
Pragadish N., Pradeep Kumar M.
doaj +1 more source
Microstructural evolution of a cold work tool steel after pulsed laser remelting [PDF]
Metalurgija, 2012 The aim of this study is the investigation of micro-structural behaviour of a Mat. No. 1.2379 (EN-X160CrMoV121; AISI D2) cold work tool steel after remelting with a precise pulsed Nd:YAG laser.
L. Kosec +3 more
doaj +2 more sources
Journal of Manufacturing and Materials Processing, 2022 The success of the thixoforming process largely depends on the created microstructure, which must be globular in the liquid phase. The solid–liquid structural changes that occur on as-annealed D2 tool steel when it is subjected to the so-called DPRM are ...
M. N. Mohammed +7 more
doaj +1 more source
MITIGATION OF AGRICULTURAL ENERGY REQUIREMENT IN BANGLADESH USING MICROALGAE PRODUCTION [PDF]
Journal of Mechanical Engineering and Sciences, 2013 A high quality joint between tool steel and stainless steel alloys is hard to achieve with the conventional welding process. In this study, a new process of joining semi-solid AISI D2 tool steel and AISI 304 stainless steel using a partial remelting ...
Mohammad Farzid Hasan +3 more
doaj +1 more source
Cross-Section Bead Image Prediction in Laser Keyhole Welding of AISI 1020 Steel Using Deep Learning Architectures [PDF]
, 2020 A deep learning model was applied for predicting a cross-sectional bead image from laser welding process parameters. The proposed model consists of two successive generators.
Ki, Hyungson, Oh, Sehyeok
core +1 more source
Journal of Materials Exploration and Findings, 2023 The effect of hard chromium coating on AISI D2's mechanical properties and wear resistance has been investigated using the electrolysis technique with varying current and coating duration. The variations of current used are 0.8 A, 1.2 A, and 1.6 A, while
Indah Uswatun Hasanah +2 more
doaj +1 more source