Results 11 to 20 of about 787 (158)
Abrasive Wear of AlSi12-Al2O3 Composite Materials Manufactured by Pressure Infiltration
Archives of Metallurgy and Materials, 2016 The aim of this study is to investigate tribological properties of EN AC-AlSi12 alloy composite materials matrix manufactured by pressure infiltration of Al2O3 porous preforms.
Kremzer M. +3 more
doaj +2 more sources
AlSi12 Alaşımından Üretilen Kompresör Silindir Kapağında Abrasif Aşınma Davranışının İncelenmesi [PDF]
Düzce Üniversitesi Bilim ve Teknoloji Dergisi, 2017 Bu çalışmada havalı fren kompresör silindir kafası üretiminde kullanılan aynı kimyasal bileşime sahip fakat farklı morfolojide iki farklı AlSi12 alaşımının aşınma dirençleri incelenmiştir.
Samet Aksoy +2 more
doaj +8 more sources
The Effects of Pressure During the Crystallization on Properties of the AlSi12 Alloy [PDF]
Archives of Foundry Engineering, 2017 The paper deals with the impact of technological parameters on the mechanical properties and microstructure in AlSi12 alloy using squeeze casting technology.
Pastirčák R., Ščury J., Moravec J.
doaj +3 more sources
Fabricación y comportamiento de espumas de aluminio con diferente densidad a partir de un precursor AlSi12 [PDF]
Revista de Metalurgia, 2010 Se han fabricado espumas de aluminio de poro cerrado, de tres diferentes rangos de densidad, utilizando un precursor AlSi12 producido por pulvimetalurgia.
J. A. Gutiérrez-Vázquez, J. Oñoro
doaj +2 more sources
Düzce Üniversitesi Bilim ve Teknoloji Dergisi, 2017 In this study, abrasivewear resistance of AlSi12 alloys which are used to produce the compressor headcylinder, having same chemical composition but different microstructure, wereexamined.
Erdem Ünüvar +2 more
doaj +1 more source
Diffusion and Interdiffusion Study at Al- and O-Terminated Al2O3/AlSi12 Interface Using Molecular Dynamics Simulations. [PDF]
Materials (Basel), 2023 The equivalent characteristics of the materials’ interfaces are known to impact the overall mechanical properties of ceramic–metal composites significantly.
Tahani M, Postek E, Sadowski T.
europepmc +2 more sources
, 2022 Purpose Paper aims to an alloy development study was carried out to increase the mechanical properties of cylinder heads. Design/methodology/approach AlSi12 alloys are used to manufacture the compressor head cylinder by high-pressure casting for easy ...
Aksoy, Samet +5 more
core +2 more sources
Development and Investigation of AlSi12-Based Composites Reinforced with Saffil<sup>TM</sup> Fibers and Nickel-Coated Graphite Flakes. [PDF]
Materials (Basel)Composites based on the AlSi12 aluminum alloy reinforced with SaffilTM fibers (Composite I) and with both SaffilTM fibers and nickel-coated graphite flakes (Composite II) were developed using the squeeze casting method in the fabrication process.
Wyrwa W, Grzęda J.
europepmc +2 more sources
3D Investigation of Damage During Strain‐Controlled Thermomechanical Fatigue of Cast Al–Si Alloys
Advanced Engineering Materials, Volume 25, Issue 17, September 2023., 2023 AlSi12Cu3Ni2 alloy with reduced Cu and Mg shows a 45% increase in thermomechanical fatigue (TMF) resistance. 3D investigations reveal preferential crack initiation at large primary Si clusters. AlSi12Cu3Ni2 shows comparatively smaller primary Si clusters and damage initiation and accumulation at later TMF stages.
Katrin Bugelnig +6 more
wiley +1 more source
Advanced Engineering Materials, Volume 25, Issue 15, August 2023., 2023 Herein, the reference radius concept is applied to map the influence of geometric notches on the fatigue strength of laser beam welded joints made of AA7075 and magnetic pulse welded joints of AA7075 and 3D‐printed AlSi10Mg. It is shown that the notch stress fatigue class FAT 178 (v. Mises stress) can be applied for a reliable fatigue assessment.
Andre Jöckel +6 more
wiley +1 more source