Results 31 to 40 of about 51,955 (285)

Influence of corrosion and creep on intergranular fatigue crack path in 2XXX aluminium alloys [PDF]

, 2010
In this paper, two examples of the influence of time-dependent processes on crack path in two 2XXX aluminium alloys are presented. The first example is concerned with corrosion–fatigue crack growth resistance of a 2024 T351 alloy cracked in the S–L ...
Odemer, Grégory, Hénaff, Gilbert, Menan, Frédéric   +2 more
core   +1 more source

Grain refinement efficiency of a new oxide-containing master alloy for aluminium casting alloys [PDF]

, 2014
In this study, grain refinement efficiency of a new oxide master alloy based on MgAl2O4 was demonstrated on an A357 alloy. The grain size of the reference alloy was reduced by 50-60% with the addition of the master alloy and introduction of ultrasonic ...
Dmitry G. Eskin, Vadakke Madam Sreekumar, Nadendla Hari Babu, Sreekumar, VM, Babu, NH, Eskin, DG, Fan, ZY, Zhong Yun Fan   +7 more
core   +1 more source

Development of a super ductile diecast Al-Mg-Si alloy [PDF]

, 2012
This is the post-print version of the final paper published in Materials Science and Engineering A. The published article is available from the link below.
Watson, D, White, M, Fan, Z
core   +1 more source

Numerical Modelling and Design of Aluminium Alloy Angles under Uniform Compression

CivilEng, 2021
Research studies have been reported on aluminium alloy tubular and doubly symmetric open cross-sections, whilst studies on angle cross-sections remain limited.
Evangelia Georgantzia, Michaela Gkantou, George S. Kamaris   +2 more
doaj   +1 more source

Aluminium-Magnesium Alloys [PDF]

Science, 1900
n ...
openaire   +3 more sources

Comparative Assessment of Magnesium, Copper, and Zinc Addition to Aluminium Waste Casting for Improving Ship Material Behaviour [PDF]

TransNav
The aluminium industry for ship materials produces waste material that can pollute the environment. To protect the environment from material pollution, the aluminium waste recycling process can be used to develop ship material. This study aims to analyze
Kiryanto Kiryanto, Tuswan Tuswan, Samuel Samuel, Ahmad Firdhaus, Dio Ergana, Theo Nadiyas Juneva, Lazuardi Virman Firdaus   +6 more
doaj   +1 more source

Friction behavior of laser cladding magnesium alloy against AISI 52100 steel [PDF]

, 2012
The use of magnesium alloys in engineering applications is becoming increasingly important as a relatively low density allows savings in energy consumption and therefore reduction in air pollution.
J.E. Masse, MASSE, Jean-Eric, A. Fabre, FABRE, Agnes   +3 more
core   +1 more source

Weld residual stress effects on fatigue crack growth behaviour of aluminium alloy 2024-T351 [PDF]

, 2008
The interaction between residual stress and fatigue crack growth rate has been investigated in middle tension and compact tension specimens machined from a variable polarity plasma arc welded aluminium alloy 2024-T351 plate.
Liljedahl, CDM, Tan, M. L., Edwards, Lyndon, Irving, PE, Brouard, J, Liljedahl, C.D.M., Zanellato, O., Fitzpatrick, M. E., Zhang, Xiang, Fitzpatrick, M.E., Brouard, J., Ganguly, S, Liljedahl, C. David M., Ganguly, S., Zanellato, O, Irving, P.E., Lin, J., Tan, ML, Liljedahl, C. D. M., Edwards, L., Fitzpatrick, Michael E., Zhang, X.; id_orcid, Ganguly, Supriyo, Zhang, X., Zhang, X, Edwards, L, Zanellato, Oliver, Lin, J, Irving, P. E., Irving, Phil E., Tan, M.L., Fitzpatrick, ME   +31 more
core   +1 more source

Influence of anodizing process on fatigue life of a machined aluminium alloy [PDF]

, 2010
In order to investigate the coupled effects of machining and anodizing processes on fatigue life of alloy 7010-T7451, a series of rotating bending fatigue tests were conducted at 60Hz.
Chaussumier, Michel, Rezaï-Aria, Farhad, Chieragatti, Rémy, Mabru, Catherine, Mabru, C., Shahzad, Majid, Chaussumier, M., Rezai-Aria, F., Shahzad, M., Chieragatti, R.   +9 more
core   +1 more source

Lubricated sliding wear behaviour of aluminium alloy composites

, 2005
Interest in aluminium alloy (Al-alloy) composites as wear resistant materials continues to grow. However, the use of the popular Al-alloy-SiC composite can be limited by the abrasive nature of the SiC, leading to increased counterface wear rates.
Rainforth, W.M., Jones, H., Walker, J.C.
core   +1 more source